Canyon Lake TX Heating Cooling

HVAC System Repair Service: The client’s HVAC system was intermittently shutting down during operation due to a faulty relay switch. I replaced the defective switch and performed a comprehensive system check to ensure smooth operation, preparing the home’s heating system for consistent use during the autumn season.

Whole Home Generator Installation: A client requested the installation of a whole home generator to avoid disruptions during potential autumn storms. I installed a backup generator with automatic transfer switches, ensuring a smooth transition to backup power during outages, providing the homeowner with peace of mind.

AC Unit Replacement: In response to the homeowner’s request for a more energy-efficient cooling solution, I replaced their outdated AC system with a modern Rheem central air unit. This upgrade provides improved performance, lower energy consumption, and greater comfort for the household year-round.

AC Repairs: Responding to a client's service call for an inoperable air conditioning system, I identified a malfunctioning compressor as the root cause of the cooling failure. I replaced the compressor, restoring proper refrigerant circulation and ensuring the system operated at peak performance.

Single system cooling tune-up completed on a two-year-old horizontal gas system. The indoor unit is clean. The drain line has been cleared and treated, and the float switch is operational. The outdoor unit coils were cleaned. The refrigerant charge is within range, and all electrical is within manufacture specs. No major issues found.

Air Conditioning System Repairs: Replaced a malfunctioning defrost control board to ensure accurate defrost cycles and improve overall system efficiency.

Ductwork Inspection and Repair: Sealed leaks and improved airflow efficiency through meticulous ductwork repair, enhancing overall HVAC performance.

Indoor Air Purification Installation: Integrated a UV light air purification system into the HVAC system, improving indoor air quality by neutralizing contaminants.

Smart Thermostat Installation: Installed a smart thermostat for remote control and energy-saving features, enhancing HVAC system efficiency.

Air Conditioning Repair Service: Replenished depleted refrigerant levels to restore an AC system's cooling capacity and efficiency. Discussed maintenance plans with the homeowner.

AC System Tune-Up: Replaced a worn blower wheel during an AC tune-up, improving cooling efficiency. Discussed regular maintenance benefits with the homeowner.

AC Contactor Replacement: Replaced a malfunctioning contactor to ensure reliable AC startup and consistent operation.

AC Refrigerant Pressure Adjustment: Adjusted refrigerant pressure in an AC system to optimize cooling efficiency.

Pulled the evaporator coil and cleaned it with a strong cleaning agent. Rerouted the copper and drain line to allow a better spot for the filter to be used. Replaced the in-line filter dryer and pressure tested with dry nitrogen. Pulled a vacuum on the copper line set and charged system to factory specs. Checked operation of the system and it is working properly at this time.

Installed mobile home indoor unit and Payne exterior condenser. Installed Honeywell thermostat. Replaced disconnect and whip and ran low voltage in 1/2” Seal-Tite for outdoor condensing unit. Rebuilt drain and verified drain operation. Pressure tested and pulled a vacuum on the line set. Weighed in refrigerant charge to meet manufacturer specifications. System operational.

AC System Replacement: Upgrading an outdated and inefficient AC system, our skilled technicians swiftly installed a modern, high-efficiency model. Rigorous testing ensures optimal performance, delivering improved comfort and substantial energy savings for the homeowner. Our focus is on efficient and cost-effective AC solutions, enhancing home cooling and sustainability.

When I arrived, the customer informed me that the system was not keeping up yesterday. I turned the system on and began diagnostic. Checked refrigerant pressures and had 12° of superheat and 8° of sub cooling. I had a 19° delta T. The system is starting to get dirty however everything is working properly at this time.

Found that the drain system was clogged and should be ran in hard pipe PVC. To be completed Tuesday - Rerun drain in schedule 40 PVC. Add an SS-2 to the second drain connection on the primary pan.

When I arrived the motor and indoor air handler were completely disassembled. I installed the new blower wheel and remounted the air movement motor. I put everything back together and wired it up per specs on the unit. I turned everything on, and it is running at this time. The system is starting to get dirty and filters need to be changed at least once a month.