HVAC Service In Buda, TX

Heat check was completed on horizontal gas system. Flame sensor was cleaned. Drain line was flushed and treated. All mechanical and electrical components found within manufacturers specs. No gas leaks were detected. Before leaving, I did cycle the system on to verify proper operation.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with water. I also treated the drain line. The air filters were ready to be replaced. I did find that the safety float switches were not working. The would not trip and stop the signal from being passed through them. Options for repair were presented to the homeowner. He chose to have the safety switches replaced today. I replaced the switches and function tested the system. The system was running at the completion of service.

Performed heater tune-up on a Carrier Infinity furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. Did find a gas leak at the furnace gas shut off valve. Spoke with Mr. Herzog and he chose to have the valve replaced. I replaced the shut off valve and the flexible gas line as well. Turned the gas on and verified no other leaks were present on the system. Both surge protection devices are working. The system is operational at completion of service.

Installed Carrier 3 ton furnace. Installed Ecobee pro thermostat. Installed new disconnect and whip. Ran new low voltage wire to thermostat and condensing system. Installed new secondary drain pan. Installed new extended supply plenum and new return plenum. Attached all existing ductwork and sealed all connections. Replaced grilles downstairs. Rebuilt and insulated primary drain line. Cleared drain and verified operation. Everything is working at completion of install.

Heat check was completed on a horizontal gas system. Drain line was flushed and treated. Flame sensor was cleaned. All mechanical and electrical components were tested. All electrical connections were tightened. No gas leaks were detected. I did find the blower motor leaking lubricant all over the bottom of the blower housing. I did visit with the homeowner about all findings, he chose to replace the blower motor today. I picked up a new blower motor and returned and replaced it. I then function checked the system. The system was running at completion of service.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with water. I also treated the drain line. The condensation pump is operating normally. The air filter was clean and had been recently replaced by the homeowner. No major issues were found. The system was running at the completion of service.

Performed Heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with water. The air filter is ready to be replaced. I cleaned the condenser coil. No major issues were found. The system was running at the completion of service.

Installed new 14” return going back to the return plenum. Re hung and secured 12” supply flex for better airflow. Built, installed and sealed new supply and return air plenums. Re installed Reme Halo in supply plenum. Adjusted air flow. Tested system static pressure and temperature split.

Heat check completed on a vertical gas system. Drain was cleared and treated. Flame sensor was cleaned. All mechanical and electrical equipment found within manufacturers specifications. Air filters were clean. Gas pressures good. All electrical connections have been secured. System was verified to be heating properly at time of departure.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with water. I also treated the drain line. The air filter was clean and had been recently replaced by the homeowner. I rinsed the condenser coil. No major issues were found. The system was running at the completion of service.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with water. I also treated the drain line. The air filters were clean and had been recently replaced by the homeowner. No major issues were found. The system was running at the completion of service.

Service diagnostic found that the blower motor had failed. Options for repair were presented to the homeowner, she chose to have the blower motor replaced. I picked up the new motor from our supply house and returned to the job. I replaced the blower motor and function tested the system. The system was running at the completion of service.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

Upon arrival, I found the outdoor contactor receiving 24 volts at the low-voltage terminals and 240 volts at the line side. However, the contactor was not passing power through to the load side. Based on these findings, I informed the homeowner that the contactor required replacement. After receiving repair approval, I replaced the contactor then cycled the system on. The system is cooling properly at completion of service.

Installed new primary drain line going out the side of the house. Installed SS2 coming out of the air handler. Tested both pan and piped float switch operations. Primed drain and tested drain operation. Everything is working at completion of service

Performed AC cooling check on three systems. I cleared the condensation drain lines and flow tested the drains with water. I also treated the drain lines. The air filters were replaced with client supplied filters. I cleaned the condenser coils. No major issues were found. The systems were running at the completion of service.

Service diagnostic found the outdoor fan motor was failing. The fan motor would overheat and shutdown. I also found the outdoor contactor is getting pitted and the system is undercharged with refrigerant. At the indoor system I found the blower wheel is dirty. The blower motor is leaking oil. The indoor coil is also rusted and prone to a refrigerant leak. Spoke with the homeowner and he chose to have the outdoor fan motor replaced and add refrigerant to the system to bring it to manufacturer rating. I replaced the outdoor fan motor and added 1lb of refrigerant. I also cleaned and treated the primary drain line at no additional charge. Function tested the system and it is now operational.

Performed a/c tune-up on a American Standard heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. Did find the indoor blower wheel is accumulating dirt/dust. The indoor evaporator coil is also rusting and can be prone to a refrigerant leak in the future. At the outdoor system I found the fan motor is showing signs of overheating and the starter relay is pitted at the contacts. Went over my findings with the homeowner. The system is working at the moment but it could have more problems in the near future due to the age of the system.

Performed a/c tune-up on a Rheem two stage heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and primary pan. Replaced the AprilAire 810 filter and washed the outdoor coil. No major issues were found. The system is operational at this time.