Kyle TX Heating & Air Conditioning Services

Cooling check completed on an up-flow furnace/inverter. Indoor unit clean, air filter has been changed, and all electrical within manufacture specs. The float switch was tested and is working properly. Cleared and treated the drain line. The outdoor unit’s coil has been cleaned. The temperature split is within range and the system is operating properly at this time.

Installed Carrier gas system. Installed Ecobee thermostat. Transitioned to existing ductwork. Installed new plywood overlay for system. Installed filter base. Replaced sidewall grille. Insulated and reinforced existing trunk line. Rebuilt and insulated primary drain line. Cleared and verified drain operation. Added SS2 safety float switch. Replaced disconnect and whip at the outdoor condenser. Ran low voltage in high voltage whip. Pressure tested and pulled a vacuum on the copper line set. Weighed in charge to meet manufacturer specifications.

Cool check completed on an up-flow furnace system. Float switch is working properly. Drain line has been cleared. Blower motor capacitor is below manufacture specs. Outdoor condenser amp draws are within spec. The coil is clean and refrigerant levels are normal. Outdoor capacitor is also within spec; however, the contactor is chard and pitted. No other major issues found.

Single system cool check completed. Both coils are clean and in good condition. Primary drain line has been cleared. Blower motor capacitor is below manufacture specs. Refrigerant levels within spec and the outdoor electrical components are within value. No other major issues found. Repair options were presented to the homeowner, and they decided to have the blower motor capacitor replaced today. Completed repair and the system is operating properly at this time.

Installed Carrier heat pump system. Installed Ecobee Pro thermostat. Replaced supply plenum and sealed all connections with mastic. Installed new plywood overlay for system. Installed filter base. Rebuilt and insulated primary drain line. Cleared and verified drain operation. Added SS2 safety float switch. Replaced disconnect and whip at the outdoor condenser. Ran low voltage in 1/2-inch Seal-Tite. Installed surge protectors for both indoor and outdoor units. Pressure tested and pulled a vacuum on the copper line set. Weighed in charge to meet manufacturer specifications.

I arrived at the home to find the system off. I got straight to work with checking over the system. I made sure to rinse out the condenser coil very well and also cleared the drain. I poured a gallon of hot water down the drain afterwards. I checked over the system and found everything to be in working order. The system is operating as best as it can for being 12 years old. The system has a piston, so I checked refrigerant by superheat and found it to be within range. System is in working order at completion of appointment.

I arrived at the home to find the system off. I got straight to work with checking over the system. I made sure to rinse out the condenser coil very well and also cleared the drain. I poured a gallon of hot water down the drain afterwards. I checked over the system and found everything to be in working order. The system is operating as best as it can for being 12 years old. The system has a piston, so I checked refrigerant by superheat and found it to be within range. System is in working order at completion of appointment.

I arrived at the home to find the system off. I got straight to work with checking over the system. I made sure to rinse out the condenser coil very well and also cleared the drain. I poured a gallon of hot water down the drain afterwards. I checked over the system and found everything to be in working order. The system is operating as best as it can for being 12 years old. The system has a piston, so I checked refrigerant by superheat and found it to be within range. System is in working order at completion of appointment.

I arrived at the home to find the system off. I got straight to work with checking over the system. I made sure to rinse out the condenser coil very well and also cleared the drain. I poured a gallon of hot water down the drain afterwards. I checked over the system and found everything to be in working order. The system is operating as best as it can for being 12 years old. The system has a piston, so I checked refrigerant by superheat and found it to be within range. System is in working order at completion of appointment.

Performed AC cool check on two systems. Checked electrical, mechanical, safety, and performance of the systems. Drain lines were cleared and treated. The blower wheels are clean. Condenser fan motors and capacitors are in good condition. Refrigerant charge within spec on both systems. The attic system that conditions the living room and kitchen area has an electronic safety switch that is failing. The switch is only passing a signal intermittently causing the condenser to stop and start rapidly. No other major issues found. Options for repair were presented to the customer and he chose to have the failing safety switch replaced. Completed repair and function checked the system. Both systems were running at the time of departure.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. Supply and return plenums are clean. System sterilizers are operational. The blower wheel and evaporator coil are also clean. The wiring is tight and in good condition. The condenser fan motor is in good condition. Condenser capacitor is within value. The contractor is also in good condition. Condenser coil was cleaned. The refrigerant charge is within range and is cooling at ten degrees of sub cooling. The system was running at the time of departure.

Removed the old supply plenum and old air handler. Replaced the air handler with a new one. Replaced the secondary drain pan. Rebuilt condensate drain and added safety float switches. Installed new in line filter dryer, pressure tested with dry nitrogen and pulled and vacuum on the copper line set. Replaced the supply plenum with a new one. Charged system to factory specifications and checked operation of the system. Installed new Ecobee Lite thermostat.

Installed Carrier heat pump. Installed Ecobee Pro thermostat. Installed new supply and return plenums and sealed all connections with mastic. Replaced secondary drain pan. Rebuilt and insulated drain line. Installed SS2 and SS3 safety float switch. Cleared and verified drain operation. Installed sub panel on top on air handler. Replaced disconnect and whip at outdoor unit. Ran low voltage in 1/2-inch Seal-Tite. Replaced breaker for condenser. Weighed in charge to meet manufacturers specifications.

Single system cooling check performed. The evaporator and condensing coils are both clean and in good shape. The drain line was cleared and treated. All electrical and refrigerant levels within manufacture specs. No major issues were found, and the system is working properly at this time.

Single system cool check completed. The air filter changed and drain line cleared and treated. Both coils are in good shape and the Delta T reading is at 21°. I did find that the contactor and condenser fan motor are beginning to fail. No other major issues found. Provided repair options to the homeowner and they decided to have the contactor and condenser fan motor replaced today to avoid a potential breakdown this summer. Completed repairs and the system is operational.