Kyle TX Heating & Air Conditioning Services

I performed a complete heating maintenance inspection of the system. I inspected all high- and low-voltage wiring and connections and verified that everything was properly tightened and secure. I inspected the blower motor and assembly and found them free of buildup and biological growth. I flushed the primary drain line with hot water and CO₂ to ensure proper drainage and found no signs of blockage or restriction. The furnace heating sequence was working properly and upon completing the furnace sequence there were no signs of flame roll out or any other issues at this time After completing the maintenance, I allowed the system to operate for approximately 15–20 minutes and verified that the system is operating properly at this time.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

Service diagnostic found the outdoor capacitor had failed on the fan side. This was preventing the outdoor fan motor from turning on which was overheating the compressor and shutting down as a safety. Spoke with the homeowner on the phone and he chose to have the capacitor replaced. I replaced the capacitor and function tested the system. I also tested the primary drain line with a gallon of water and verified it is draining, at no additional charge. No other issues were found. The system is operational at completion of service.

I performed a complete heating maintenance inspection of the system. I inspected all high- and low-voltage wiring and connections and verified that everything was properly tightened and secure. I inspected the blower motor and assembly and found them free of buildup and biological growth. I flushed the primary drain line with hot water and CO₂ to ensure proper drainage and found no signs of blockage or restriction. The furnace heating mode was working properly and upon completing the furnace sequence there were no signs of flame roll out or any other issues at this time. The condenser coils were thoroughly washed and cleaned from both the inside and outside to ensure proper airflow and heat transfer. After completing the maintenance, I allowed the system to operate for approximately 15–20 minutes and verified that the system is operating properly and heating at this time.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

I performed a complete heating maintenance inspection of the system. I inspected all high- and low-voltage wiring and connections and verified that everything was properly tightened and secure. I inspected the blower motor and assembly and found them free of buildup and biological growth. I flushed the primary drain line with hot water and CO₂ to ensure proper drainage and found no signs of blockage or restriction. The furnace heating sequence was working properly and upon completing the furnace sequence there were no signs of flame roll out or any other issues found. The condenser coils were thoroughly washed and cleaned from both the inside and outside to ensure proper airflow and heat transfer. After completing the maintenance, I allowed the system to operate for approximately 15–20 minutes and verified that the system is operating properly and cooling and heating at this time.

I performed a complete heating maintenance inspection of the system. I inspected all high- and low-voltage wiring and connections and verified that everything was properly tightened and secure. I inspected the blower motor and assembly and found them free of buildup and biological growth. I flushed the primary drain line with hot water and CO₂ to ensure proper drainage and found no signs of blockage or restriction. The furnace heating sequence was working properly and upon completing the furnace sequence there were no signs of flame roll out or any other issues found. The condenser coils were thoroughly washed and cleaned from both the inside and outside to ensure proper airflow and heat transfer. After completing the maintenance, I allowed the system to operate for approximately 15–20 minutes and verified that the system is operating properly and cooling at this time.

Performed heat check on two systems. Checked the electrical, mechanical, safety, and performance of the systems. I cleared the condensation drain lines and flow tested the drains with water. I also treated the drain lines. The air filters were clean and had been recently replaced by the homeowner. No major issues were found. The systems were running at the completion of service.

Performed heater tune-up on a Carrier furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line. Also function tested the a/c system and found the outdoor fan motor is developing a hot spot. We will continue to monitor the motor on our next visit. No other issues were found. The system is operational at this time.

Heat check was completed on a horizontal gas furnace. Drain line was flushed and treated. Flame sensor was cleaned. All mechanical and electrical were checked and found within manufacturer specifications. No issues were found with the furnace or furnace operation. The system is without surge protection. I also noticed multiple supply vents are dirty indicating ducting is not properly sealed. I did go over all findings with the homeowners. Furnace was fully operational at time of departure.

Heat check was completed for a horizontal gas furnace. Drain line was flushed and treated. Flame sensor was cleaned. All mechanical and electrical components were checked and found within manufacturer specifications. I did secure all thermostat wiring and harness plugs. System was cycled to verify proper operation. No major issues were found.

During the inspection, I found that the float switch was not tripped but was covered in biological growth. The partial drain line was also clogged with a significant amount of slime and standing water. The primary drain pan contained a large amount of buildup and debris. After clearing the drain line, I also shop-vacuumed the primary drain pan to remove the buildup and ensure there were no restrictions that could contribute to future drainage issues. I then flushed approximately four gallons of hot water through the drain line to verify proper drainage. I inspected the outdoor condenser, the condenser fan motor is showing signs of excessive heat during operation. There was no oil present around the motor, and the fan blade was spinning freely. I informed the homeowner that the motor should be monitored for any changes in performance. The condenser coils were dirty, I removed the top to wash the coil inside and out. The system is operating normally at the completion of service.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filters were replaced with client supplied filters. No major issues were found. The system was running at the completion of service.

I performed a complete heater maintenance inspection of the system. I inspected all high- and low-voltage wiring and connections and verified that everything was properly tightened and secure. I went over the heating sequence and cleaned the flame sensor to ensure there is no build on the sensor. I checked the gas pressure and found it within range for manufacturer specifications. The inducer motor is amping within range as well, no signs of seizing motor or any issues. I ensured there was no roll out on the completion of the heating sequence. I inspected the blower motor and assembly and found them free of buildup and biological growth. I flushed the primary drain line with hot water and CO₂ to ensure proper drainage and found no signs of blockage or restriction. I allowed the system to operate for approximately 15–20 minutes and verified that the system is operating properly at this time.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with water. I also treated the drain line. The air filter was clean and had been recently replaced by the homeowner. No major issues were found. The system was running at the completion of service.