Kyle TX Heating & Air Conditioning Services

Performed heater tune-up. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filters are still in clean condition as they have just been replaced by the homeowner. No major issues were found, and the system is running at the completion of service.

Installed new secondary drain pan. Installed new SS2 and SS3 safety float switches. Rebuilt and insulated primary and secondary drain line. Cleared drain and verified proper operation. Cleaned indoor coil in place. Re-crimped low voltage connections in air handler. Resealed all duct take offs and plenums to the unit. Cleaned the outdoor condenser and condensing coil. Installed new condenser fan motor. Replaced surge protectors in electrical box. Replaced contactor. Cycled system multiple times to ensure operation. Everything is operational at this time.

Recovered existing refrigerant. Installed new Mitsubishi compressor. Pressure tested system with nitrogen and pulled a vacuum. Weighed in factory charge of R-410A refrigerant. Tested heating and cooling operation on each head. All are working at this time.

Performed a heater tune-up on a Rheem heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. I replaced the return air filter and taped around the filter to prevent any filter bypass. I washed the outdoor coil. I found that the outdoor condenser fan motor is leaking lubricant. I also found oil stains on the indoor coil, so I completed a leak check but did not find any leaks. No other major issues found.

Performed a heater tune-up on a Carrier heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. The air filters were replaced recently by the homeowner and they are still in clean condition. I washed the outdoor coil and secured the compressor wiring to prevent any wire rub outs. No major issues were found, and the system is operational at this time.

Performed heater tune-up. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the system with two gallons of water. I also treated the drain line. The air filter was replaced with a customer supplied filter. No major issues were found, and the system is running at the completion of service.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. I cleared the condensate drain line and flow tested the drain with two gallons of water. I then treated the drain line. The air filter was replaced with a customer supplied filter. The condenser coil was cleaned. I found two small holes in the ductwork about the size of a pencil eraser and I sealed them up at no additional charge. I also cleaned the flame sensor on the furnace. No other major issues were found, and the system is running at the completion of service.

Installed new extended supply plenum. Installed new horizontal return plenum. Installed new return air filter grille and plenum. Ran new flex back to return. Installed new 12x12 return bucket and ran new flex. Sealed all connections with mastic air lock.

Heating tune-up completed on a horizontal furnace. I found that the blower wheel is dirty, and the blower capacitor is below value. No other major issues found.

Performed heater tune-up. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the system with two gallons of water. I also treated the drain line. Filters were replaced with customer supplied filters. No major issues were found. The system was set to the customer’s desired temperature, and the system was running at the time of departure.

Heating maintenance completed on a two-year-old horizontal Trane gas system. I did find that the gas pressure was off, so I adjusted it to meet manufacturer specifications. No other major issues found at this time.

Performed heater tune-up. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. No major issues were found, and the system is running at the completion of service.

Performed heater tune-up. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain. No other major issues were found, and the system is running at the completion of service.

Performed heater tune-up. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. The filter was replaced with a customer supplied filter. No major issues were found, and the system is running at the completion of service.

Performed semiannual maintenance on one heat pump heating system. Inspected all Performance, Mechanical and Safety systems. Verified everything was operating within manufacture specifications for operation. Everything is working at this time.