Kyle TX Heating & Air Conditioning Services

Replaced the existing supply plenum and reinstalled the drip shield. Upsized the supply bucket and grille in the office room. Reinstalled the air purifier in the supply plenum and sealed all the connections with mastic. Checked operation of the system and it is working properly at this time.

Replaced the existing supply plenum and reinstalled the drip shield. Upsized the supply bucket and grille in the office room. Reinstalled the air purifier in the supply plenum and sealed all the connections with mastic. Checked operation of the system and it is working properly at this time.

Heater tune-up completed on a heat pump package unit. No major issues found at this time.

Performed heater tune-up on a Carrier gas furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. I replaced the high voltage wire nuts with a Wago wire connector. I replaced the return air filter. I also found the compressor wire at the outdoor condenser was starting to rub out. I secured the wiring to prevent any electrical damage. I checked the static pressure of the system and found that the fan speed was set to deliver 920 cfm on a 2.5-ton system. This air flow is correct for this size system but my total static reading is still higher than recommended at .7. No other major issues were found, and the system is operational at this time

Performed heater tune-up on a Carrier heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. I replaced the air filter and then used foam tape to seal around the return filter to prevent any filter bypass. I then washed the outdoor condenser unit and cycled power. No major issues were found, and the system was left off at the thermostat per customer request.

Performed semiannual maintenance on one heat pump heating system. Inspected all Performance, Mechanical and Safety systems. Tested and verified everything was operating within manufactures specifications for operation. Everything is working at this time.

Performed heater tune-ups on two systems. Checked electrical, mechanical, safety, and performance of the systems. I cleared the drain lines and flow tested them with two gallons of water. I also treated the drain lines. The system for the living area of the home has a capacitor that is below value on the condenser unit. I presented my findings to the homeowners, and they chose to have the capacitor replaced today. I replaced the capacitor and function tested the system. Both systems are running at the completion of service.

Completed the heating tune-up on a horizontal furnace. No major issues found at this time.

Performed whole home duct sealing with air lock and silicone. Also sealed the return and supply plenums. Verified system operation in heat and cool. Everything is working at the is time.

Performed semiannual maintenance on one heat pump heating system. Inspected all Performance, Mechanical and Safety systems. Ensured everything was working within manufactures specifications for operation. I did change out a 20x25x2 air filter that the homeowner provided. Everything is working at this time.

Heating tune-up completed on a vertical furnace. No major issues found with the eight-year-old system.

Performed the heater tune-up on a Carrier gas system. Checked electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. I replaced the high voltage wire nuts with a Wago wire connector. I sealed some areas of the furnace that were pulling unfiltered attic air into the home with mastic tape. I used a gasket and sealed around the filters to prevent any filter bypass. I found the blower capacitor is below value and the blower wheel is dirty. I spoke with the homeowners and they chose to have the blower capacitor replaced at this time. I replaced the blower capacitor and cycled power. The system is operational at this time.

Furnace Repair Service – I attended to a homeowner experiencing an issue where the furnace would blow cold air intermittently. My examination showed that the flame sensor was dirty and unable to detect the flame properly. I cleaned and repositioned the sensor to restore the furnace’s ability to heat consistently, ensuring a warm and comfortable home.

Furnace Repair – A client contacted us when their furnace was failing to distribute warm air throughout the house. My inspection revealed a blocked flue pipe, which was causing the system to shut down as a safety measure. I cleared the obstruction, allowing the furnace to function properly and distribute heat effectively. I also tested the flue for proper ventilation to ensure safety.

Heating tune-up completed on a vertical gas system. I found that the blower motor is slightly over amping which is the initial sign of possible failure. No other major issues found.