Kyle TX Heating & Air Conditioning Services

Performed cool check. I found a partial clog in the condensate line. I cleared the drain with compressed air, flushed it will water, and then treated it with drain treatment. During my inspection of the outdoor unit, I found an overheated fan motor. No other major issues found.

Performed cool check. I found a partial clog in the condensate line. I cleared the drain with compressed air, flushed it will water, and then treated it with drain treatment. During my inspection of the outdoor unit, I found an overheated fan motor. No other major issues found.

Performed cool check. I found a partial clog in the condensate line. I cleared the drain with compressed air, flushed it will water, and then treated it with drain treatment. During my inspection of the outdoor unit, I found an overheated fan motor. No other major issues found.

Performed heater tune-up. I cleared the drain line and flushed it with two gallons of water. I then treated the drain line. No major issues found.

Performed heater tune-up. I cleared the drain line and flushed it with two gallons of water. I then treated the drain line. No major issues found.

Performed heater tune-up. I cleared the drain line and flushed it with two gallons of water. I then treated the drain line. No major issues found.

Performed heater tune-up. I cleared the drain line and flushed it with two gallons of water. I then treated the drain line. No major issues found.

Performed heater tune-up on a Carrier Infinity gas system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. I replaced the high voltage wire nuts with a Wago wire connector. The homeowner supplied filter for replacement. No major issues were found, and the system is operational at this time.

On arrival, I spoke with the homeowner who stated that he heard the outdoor heat pump unit making a hissing noise he had never heard before. I went outside and removed the fan shroud to find that the compressor wiring harness had rubbed out on the copper refrigerant line of the compressor causing it to arch and create a hole in the copper blowing out the entire refrigerant charge and tripping the low pressure switch on the heat pump. Also noted that the condenser fan motor has overheated and is showing signs of wear and tear. Recommend having the damaged piece of copper replaced, changing out the bi-flow filter dryer, pressure testing system, pulling a triple evacuation on the system to remove all moisture and contaminants from system and recharging the system with clean virgin refrigerant back to factory specifications. Also recommend having the condenser fan motor replaced. Removed damaged copper piece from heat pump system, installed new connections and pressure tested u

Performed semiannual maintenance on one gas heating system. Inspected all Performance, Mechanical and Safety systems. Verified everything was operating within the manufacture’s specifications for operation. Everything is working at this time.

nstalled new 5-ton Dual Fuel Carrier system. Installed 2 new Ecobee Pro thermostats. Rebuilt and insulated condensate drain line. Added SS2 and SS3 safety float switches. Cleared drain line with CO2 and flushed drain with water to ensure proper operation followed by Viper drain treatment. Installed new filter dryer, pressure tested with dry nitrogen and pulled a vacuum on copper line set. Replace the condenser pad. Replaced the disconnect and electrical whip and ran the low voltage in Seal-Tite. Replaced both the supply and return plenums and then sealed with a mastic airlock. Replaced all the zoning equipment and zone board. Installed a new 30x14 return in the loft area upstairs. Charged system to factory spec and performed a benchmark. System is working properly at time of departure.

Performed heater tune-up. I cleared the drain line and then flushed it with a gallon of water. I then treated the drain line. I also changed all three filters. No major issues found.

Performed heater tune-up. I cleared the drain line and then flushed it with a gallon of water. I then treated the drain line. I also changed all three filters. No major issues found.

Performed heater tune-up. I cleared the drain line and then flushed it with a gallon of water. I then treated the drain line. I also changed all three filters. No major issues found.

Performed heater tune-up. I cleared the drain line and then flushed it with a gallon of water. I then treated the drain line. I also changed all three filters. No major issues found.