Kyle TX Heating & Air Conditioning Services

Removed the blower motor housing from the furnace and the furnace control board from the housing. I then took the blower motor assembly outside, disassembled everything, and then thoroughly cleaned the blower wheel using a cleaning solution, scrub brush and water. While the housing was drying outside, I went inside and cut out a section of PVC pipe to install a water sensing cutoff device to protect the home from any condensation produced by the system in the event of a clogged drain. This device will shut the outdoor unit down and prevent any more condensation from producing and overwhelming the drain line. I then installed the indoor and outdoor surge protection devices on the furnace and the condenser. I then reassembled the blower motor assembly and reinstalled it into the system. Cycled system and it is operational at completion of services.

I performed the semi-annual heating maintenance on one gas furnace located in the attic of the home. I inspected the performance, safety and mechanical systems of the furnace during this visit. While testing the furnace I did have to make an adjustment to the fuel pressure being delivered to the burners of the furnace. I did this to ensure the furnace was not under fired and capable of producing the rated BTU’s of heat for the home. As part of the extended service I cleared, cleaned, flushed and treated the condensate drain to help prevent any clogs that may have developed while using the cooling side of the HVAC system. The condensate drain does empty into the P-trap for the sink in the upstairs bathroom. The furnace was operational at completion of the service.

Performed heater tune-up. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared, and flow tested with two gallons of water. The drain line was then treated. Flame sensors were cleaned. No major issues were found, and the system is running at the time of departure.

Heating tune-up completed on a vertical gas system. I found that the blower wheel assembly is dirty and there is low gas pressure exiting the gas valve. I adjusted gas pressure to be within manufactures specs. No other major issues found.

Performed heating maintenance on a gas system. Checked all electrical, mechanical and performance of the system. Cleared the drain line and cleaned the exterior of the furnace. I also removed a drain cap for better drainage flow and the customer supplied a filter for replacement. I replaced the high voltage wire nuts with the correct size and a Wago connection. I did find that there is no water safety switch on the secondary drain line and the blower wheel is dirty. No other major issues found.

Performed system heater tune-up. No major issues found.

Performed system heater tune-up. No major issues found.

Performed system heater tune-up. No major issues found.

Performed system heater tune-up. No major issues found.

Performed heating maintenance on a furnace system. Checked all electrical mechanical and performance of the system. Cleared the drain line and cleaned the exterior of the furnace. I replaced the perfect fit filter for the customer. The thermostat had some corrosion around the batteries so it was not operating correctly. The customer chose to have the thermostat replaced at this time. I replaced the thermostat and cycled power and confirmed operation in heating and cooling.

Performed semiannual maintenance on one gas heating system. Inspected all Performance, Mechanical and Safety systems. Changed out one Honeywell 20x25x4 F100 filter provided by the homeowner. Adjusted fuel pressures of the two-stage gas furnace and ensured all mechanical components were operating within manufacture’s specifications for operation. Everything is working at this time.

Heating tune-up performed on a horizontal gas system. We did find that the system has high static pressure and were able to resolve the issue by dropping the fan speed. No other major issues found.

Performed heating maintenance on a gas system. Checked all electrical, mechanical, safety and performance of the system. Cleared and treated the drain line. Vacuumed the return air chase and the furnace closet. I did find that the blower wheel is dirty, and the system is 21 years old. Due to the age of the system, we should start planning for replacement in the future. I presented these findings to the homeowner. No major issues found today.

Performed heater tune-up. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared, and flow tested with two gallons of water. The drain line was then treated. Flame sensor was cleaned. No major issues found.

Heating tune-up completed on a horizontal gas system. No major issues were found, and the system is operating within manufactures specs.