Kyle TX Heating & Air Conditioning Services

I arrived at the home to find the system on and running. I spoke to homeowners about how the system had been performing. I checked over the system and discovered the following: the contactor was pitted and charred, the capacitor was starting to get weak, and the bucket in the laundry room wasn’t sealed to the sheetrock. I made the homeowner a few options and she elected to move forward with my best option. Details are below: “Includes replacement of the capacitor, contactor, and silicone sealing of laundry room grille that is sweating.” I sealed the grille with silicone to stop the attic air from coming into the living space. I then went outside and replaced the contactor and the capacitor. I tested the system and everything came on and ran. System is in working order at completion of appointment.

I arrived at the home to find the system off and not running. I spoke to Sam about how the unit had been performing. I made sure to clear the drain and also rinse the condenser coil. I checked over the system and discovered everything to be working well. All minor and major components are working properly on the system. The refrigerant is proper as well. I recommended to the homeowner that she get more filters and start installing them at the coil, instead of the door, for better filtration. System is in working order at completion of appointment.

I arrived at the home to find the system off and not running. I spoke to Sam about how the unit had been performing. I made sure to clear the drain and also rinse the condenser coil. I checked over the system and discovered everything to be working well. All minor and major components are working properly on the system. The refrigerant is proper as well. I recommended to the homeowner that she get more filters and start installing them at the coil, instead of the door, for better filtration. System is in working order at completion of appointment.

I arrived at the home to find the system off and not running. I spoke to Sam about how the unit had been performing. I made sure to clear the drain and also rinse the condenser coil. I checked over the system and discovered everything to be working well. All minor and major components are working properly on the system. The refrigerant is proper as well. I recommended to the homeowner that she get more filters and start installing them at the coil, instead of the door, for better filtration. System is in working order at completion of appointment.

I arrived at the home to find the system off and not running. I spoke to Sam about how the unit had been performing. I made sure to clear the drain and also rinse the condenser coil. I checked over the system and discovered everything to be working well. All minor and major components are working properly on the system. The refrigerant is proper as well. I recommended to the homeowner that she get more filters and start installing them at the coil, instead of the door, for better filtration. System is in working order at completion of appointment.

Service diagnostic found that the blower motor has failed. I jumped the wiring to run the blower motor. The motor was getting power and would initially start up. However the fan was not running at the right speed. After a couple minutes it died and stopped. Options for repair where presented to the customer. He chose to have the blower motor replaced. Blower motor was replaced. System was function checked and was running at the time of departure.

Cool check completed on an up-flow gas system. The customer stated that they prefer the thermostat at 65 degrees. The indoor unit is clean, and I changed the air filter. The drain line was cleared and treated, and the float switch was checked and is operational. The outdoor coils were cleaned. The contactor is within value. The condenser fan should be monitored as I found signs of overheating. The contactor is in fair condition. The refrigerant level is providing a subcool of 7 degrees but calls for 11 degrees. No other major issues found.

Cool check completed on a horizontal gas system. Upon initial inspection, I noticed some condensation on the outside of evaporator coil casing. I also found two very dirty air filters. There are no new filters onsite, so I recommended the homeowner replace them ASAP. I have removed them from the system, so they don’t restrict airflow. I cleared the drain line and then treated it. I checked the float switch, and it is operational. The condenser coils have been cleaned. The fan motor and capacitor are in condition. The contactor is charred and pitted. The R-22 refrigerant levels may be just slightly low and should be monitored in the future. No other major issues found.

I made sure to rinse out the outdoor coil and also clear and treat the drain. I performed an evaluation of the system and discovered the following: the disconnect outside is aged with pitted contacts and hard to open, the contactor is pitted and charred, the condenser fan motor is leaking oil, and the start kit has failed. I brought all of this to the attention of the homeowner and made him a few options. He elected to move forward with a custom option of his choosing. Details are below: “Includes replacement of the condenser fan motor, contactor, and start assist kit.” I programmed and replaced the condenser fan motor. I then replaced the start kit and contactor. I made sure everything was nice and tight. I tested the system, and everything came on and ran properly. I observed a lower inrush current on the compressor. System is in working order at completion of appointment.

I made sure to rinse out the outdoor coil and also clear and treat the drain. I performed an evaluation of the system and discovered the following: the disconnect outside is aged with pitted contacts and hard to open, the contactor is pitted and charred, the condenser fan motor is leaking oil, and the start kit has failed. I brought all of this to the attention of the homeowner and made him a few options. He elected to move forward with a custom option of his choosing. Details are below: “Includes replacement of the condenser fan motor, contactor, and start assist kit.” I programmed and replaced the condenser fan motor. I then replaced the start kit and contactor. I made sure everything was nice and tight. I tested the system, and everything came on and ran properly. I observed a lower inrush current on the compressor. System is in working order at completion of appointment.

I made sure to rinse out the outdoor coil and also clear and treat the drain. I performed an evaluation of the system and discovered the following: the disconnect outside is aged with pitted contacts and hard to open, the contactor is pitted and charred, the condenser fan motor is leaking oil, and the start kit has failed. I brought all of this to the attention of the homeowner and made him a few options. He elected to move forward with a custom option of his choosing. Details are below: “Includes replacement of the condenser fan motor, contactor, and start assist kit.” I programmed and replaced the condenser fan motor. I then replaced the start kit and contactor. I made sure everything was nice and tight. I tested the system, and everything came on and ran properly. I observed a lower inrush current on the compressor. System is in working order at completion of appointment.

I made sure to rinse out the outdoor coil and also clear and treat the drain. I performed an evaluation of the system and discovered the following: the disconnect outside is aged with pitted contacts and hard to open, the contactor is pitted and charred, the condenser fan motor is leaking oil, and the start kit has failed. I brought all of this to the attention of the homeowner and made him a few options. He elected to move forward with a custom option of his choosing. Details are below: “Includes replacement of the condenser fan motor, contactor, and start assist kit.” I programmed and replaced the condenser fan motor. I then replaced the start kit and contactor. I made sure everything was nice and tight. I tested the system, and everything came on and ran properly. I observed a lower inrush current on the compressor. System is in working order at completion of appointment.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The evaporator coil and air handler are clean. The blower wheel is also clean. System sterilizers are operational. The wiring is tight and in good condition. The drain line was cleared and treated. The condenser fan motor and contactor are in good condition. The capacitor for the condenser unit is within value. The refrigerant charge is within factory specifications. The condenser coil was cleaned. No major issues were found, and the system is running at the time of departure.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. The blower wheel is clean. The wiring is tight and in good condition. The capacitor for the blower motor is within value. The zone dampers are operational. The condenser fan motor and contactor are in good condition. The capacitor for the condenser unit is within value. The refrigerant charge is within factory specifications. The condenser coil was cleaned. No major issues were found, and the system is running at the time of departure.

Cool check completed on a horizontal gas system. The furnace is clean, and the wires were tightened. The drain line was cleared and treated. I checked the float switch, and it is operational. The filter is in clean condition. The outdoor condenser coil was cleaned. All electrical is within manufacture specs. I did find that the refrigerant charge is low. Performed a leak search and found a leak in the coil. Presented my findings to the homeowner and they chose to have refrigerant added today. Refrigerant was added today and system is cooling properly at this time.