Kyle TX Heating & Air Conditioning Services

I arrived at the home to find the system off and not running. Homeowner let me know that no air was moving but the outdoor unit was running before he shut it off. I went into diagnostics over the unit and discovered that the blower motor has failed. I brought this information to homeowner and made him an option to replace the motor under his parts warranty. Patrick elected to move forward with the repair today. I replaced the motor and tested it afterwards. Everything fired up properly. I went outside and checked over the rest of the system. I also made sure to rinse the condenser coils out. System is in working order at completion of appointment.

I turned the unit on, and I was able to hear the rumbling noise the homeowners were concerned about. I went into the attic and did an evaluation of the system. I discovered the following: both zone dampers have stuck shut which is causing the excessive noise from the blower motor. The vanes on the blower wheel have also started to pull away from the wheel assembly. This is causing the excessive vibration noise that they are hearing. Also, the blower motor is leaking oil. Lastly, the zone board is original to the home. I spoke to customer about what was going on and asked how she wanted to proceed. For the time being she has elected to have me manually open the dampers and remove them from the zone board. I was able to restore proper airflow to the system. System is working to the best of its ability at this time.

I turned the unit on, and I was able to hear the rumbling noise the homeowners were concerned about. I went into the attic and did an evaluation of the system. I discovered the following: both zone dampers have stuck shut which is causing the excessive noise from the blower motor. The vanes on the blower wheel have also started to pull away from the wheel assembly. This is causing the excessive vibration noise that they are hearing. Also, the blower motor is leaking oil. Lastly, the zone board is original to the home. I spoke to customer about what was going on and asked how she wanted to proceed. For the time being she has elected to have me manually open the dampers and remove them from the zone board. I was able to restore proper airflow to the system. System is working to the best of its ability at this time.

I turned the unit on, and I was able to hear the rumbling noise the homeowners were concerned about. I went into the attic and did an evaluation of the system. I discovered the following: both zone dampers have stuck shut which is causing the excessive noise from the blower motor. The vanes on the blower wheel have also started to pull away from the wheel assembly. This is causing the excessive vibration noise that they are hearing. Also, the blower motor is leaking oil. Lastly, the zone board is original to the home. I spoke to customer about what was going on and asked how she wanted to proceed. For the time being she has elected to have me manually open the dampers and remove them from the zone board. I was able to restore proper airflow to the system. System is working to the best of its ability at this time.

I turned the unit on, and I was able to hear the rumbling noise the homeowners were concerned about. I went into the attic and did an evaluation of the system. I discovered the following: both zone dampers have stuck shut which is causing the excessive noise from the blower motor. The vanes on the blower wheel have also started to pull away from the wheel assembly. This is causing the excessive vibration noise that they are hearing. Also, the blower motor is leaking oil. Lastly, the zone board is original to the home. I spoke to customer about what was going on and asked how she wanted to proceed. For the time being she has elected to have me manually open the dampers and remove them from the zone board. I was able to restore proper airflow to the system. System is working to the best of its ability at this time.

Service diagnostic found that the capacitor on the condenser unit has failed. Options for repair were presented to the customer. The customer chose to have the capacitor replaced today. I replaced the capacitor and function checked the system. The system is now operational. As a courtesy, I also rinsed off the condenser unit and the surrounding pad. The system was running at the time of departure.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. The blower wheel is clean. Refrigerant charge is within factory specifications. The condenser fan motor is in good condition. Surge protection for the condenser unit is operational. The condenser coil was cleaned. No major issues were found, and the system was running at the time of departure.

Service diagnostic found that the low voltage fuse had blown. I used my fuse tester to check the system and the system would short on a call for cooling. I went through the entire system checking connections and looking for problems. I remade several connections through the circuits while doing so. I also isolated the thermostat to make sure the thermostat was not causing the short. After I put everything back together, I cycled the system on and off three times and it was operational each time. The system was running at the time of departure.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. The blower wheel is clean, electrical wiring is tight and in good condition, and the filter was replaced with a customer supplied filter. Condenser coil clean. The contractor and condenser fan motor are in good condition. Capacitor is within value. Refrigerant charge is within factory specifications. No major issues were found, and the system is running at the time of departure.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. The blower wheel is clean, the filter was replaced with a customer supplied filter, and the low voltage wiring was tightened. There was tape holding the door switch down; I removed the tape so the shut off switch can function. There was also a wire gap where signal wiring penetrated to the furnace control board. I used tape to seal and insulate the gap. Condenser coil was cleaned. The contactor, condenser fan motor and disconnect are in good condition. The refrigerant is within factory specifications. The capacitor for the condenser unit is well below value. No other major issues found. Options for repair were presented to the customer and Steve chose to have the capacitor replaced today. I replaced the capacitor for the condenser unit and function checked the system. I also treated the electrical cabinet with JS insecticide. The syst

Installed new 2.5-ton Carrier straight cool system. Installed new Ecobee Pro thermostat. Replaced supply plenum and sealed with a mastic airlock. Rebuilt and insulated condensate drain line. Added SS2 safety float switch. Cleared drain line with CO2 and ran 3 gallons of water down the drain to ensure proper operation. We then ran Viper drain treatment through the drain. Installed new filter dryer, pressure tested with dry nitrogen and pulled a vacuum on copper line set. Added condenser pad. Replaced the disconnect and ran the low voltage in Seal-Tite. Installed hard start kit onto the condenser. Dug a French drain and put pond rock into the hole. Charged system to factory spec and performed a benchmark. The system is working properly at time of departure.

I arrived at the home to find the system off and not running. I checked over the system and discovered that the drain line is clogged and the float switch is tripped. I cleared and treated the drain. I also followed the drain up with 1 gallon of hot water. Everything is draining properly. I went outside and checked the rest of the system and found everything to be working properly. I checked refrigerant pressures as well as the capacitor and it’s all working fine. System is in working order at completion of appointment.

I arrived at the home to find the system off and not running. I checked over the system and discovered that the drain line is clogged and the float switch is tripped. I cleared and treated the drain. I also followed the drain up with 1 gallon of hot water. Everything is draining properly. I went outside and checked the rest of the system and found everything to be working properly. I checked refrigerant pressures as well as the capacitor and it’s all working fine. System is in working order at completion of appointment.

I arrived at the home to find the system off and not running. I checked over the system and discovered that the drain line is clogged and the float switch is tripped. I cleared and treated the drain. I also followed the drain up with 1 gallon of hot water. Everything is draining properly. I went outside and checked the rest of the system and found everything to be working properly. I checked refrigerant pressures as well as the capacitor and it’s all working fine. System is in working order at completion of appointment.

I arrived at the home to find the system off and not running. I checked over the system and discovered that the drain line is clogged and the float switch is tripped. I cleared and treated the drain. I also followed the drain up with 1 gallon of hot water. Everything is draining properly. I went outside and checked the rest of the system and found everything to be working properly. I checked refrigerant pressures as well as the capacitor and it’s all working fine. System is in working order at completion of appointment.