Kyle TX Heating & Air Conditioning Services

Single system cool check completed and an up-flow gas system. Amp draws within range. The float switch is operational, and I cleared and treated the drain line. Outdoor condenser coils cleaned. The capacitor is below manufacture spec and the contactor is charred and pitted. The customer has opted to have both the contactor and capacitor replaced today. The thermostat was cycled, and the system is cooling properly at this time.

Air Conditioning Installation Service: I arrived at the client’s home to install a new AC system. I expertly set up a new Lennox central air conditioning system for a homeowner seeking cool comfort during hot summer months. From selecting the right unit to meticulous installation, I ensured optimal cooling efficiency and comfort for the entire household.

HVAC System Repair Service: During my visit to the client's residence, I diagnosed the issues plaguing their HVAC system, which stemmed from a faulty start capacitor leading to startup failures. To restore reliable startup and operation, I promptly replaced the defective start capacitor, ensuring the smooth functioning of the HVAC system.

I cleared the drain line as well as rinse out the condenser outside. I checked over the system and found everything to be in great shape. I switched some of the long quarter inch return air filter grille screws to wood screws per customer request so the filter was easier to put in. Everything outside checked out as well. System is in working order at completion of appointment.

I cleared the drain line as well as rinse out the condenser outside. I checked over the system and found everything to be in great shape. I switched some of the long quarter inch return air filter grille screws to wood screws per customer request so the filter was easier to put in. Everything outside checked out as well. System is in working order at completion of appointment.

I cleared the drain line as well as rinse out the condenser outside. I checked over the system and found everything to be in great shape. I switched some of the long quarter inch return air filter grille screws to wood screws per customer request so the filter was easier to put in. Everything outside checked out as well. System is in working order at completion of appointment.

I cleared the drain line as well as rinse out the condenser outside. I checked over the system and found everything to be in great shape. I switched some of the long quarter inch return air filter grille screws to wood screws per customer request so the filter was easier to put in. Everything outside checked out as well. System is in working order at completion of appointment.

Installed Stage 3 and Stage 4 Breathe Easy packages. System cycled and Breathe Easy packages operational.

Removed the old TXV from the upstairs system. Installed new TXV. Removed the filter dryer that was by the condenser and installed a new one in the closet near the indoor system. Pressure tested with dry nitrogen and pulled a vacuum on the copper line set. Charged system to factory specs and checked full operation of the system.

Installed Carrier system. Installed Ecobee thermostat. Installed new return plenum. Installed new UV lights. Reused and installed supply plenum and sealed all connections with mastic. Replaced secondary drain pan. Rebuilt and insulated primary and secondary drain lines. Installed SS2 and SS3 safety float switches. Cleared, treated and verified drain operation. Installed disconnect and whip for indoor air handler. Pressure tested and pulled a vacuum on the line set. Weighed in charge to meet manufacturers specifications.

Performed cooling maintenance on a straight cool system. Checked all electrical, mechanical and performance of the system. As I was doing the tune-up, I found that the primary drain line was clogged, and water was in the secondary drain pan. I removed as much water as I could from the pan. I then cleared and treated the drain. I continued my inspection and found that there is no water safety switch. I also found that the outdoor capacitor is below value on the herm side. I spoke to the customer and they chose to have the blower wheel replaced, a new capacitor installed at the condenser, and water safety switch installed on the secondary drain line. I completed the repairs and cycled power at the thermostat. The system is operational at this time.

Performed service diagnostic. Diagnostic found that the primary condensate drain line was clogged. Options for repair were presented to the customer and he chose to have the drain line cleared today. I cleared the condensation drain and flow tested it with water. I then treated the drain line. System was function checked and was running at the time of departure.

Performed service diagnostic. Diagnostic found that the capacitor on the condenser unit has failed. The failed capacitor was preventing the compressor from running and therefore the system was not cooling. Options for repair were presented to homeowner and he chose to have the capacitor replaced today. I replaced the capacitor and function checked the system. The system was running at the time of departure.

Cool check completed for seven-year-old furnace and condenser. Furnace electrical examined. Amp draw is normal on the blower motor. The drain line was flushed, and the float switch is operational. Outdoor condenser coils clean. Refrigerant level with spec. All electrical within manufacture specs. No major issues found at this time. System is cooling properly.