Wimberley TX Heating & Air Conditioning Services

Performed heating maintenance on one heat pump system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. I found that all three UV lights had tripped the 3-amp transformer. I installed another transformer and separated one of the lights. All UV lights and surge protectors are on and working. No other major issues were found. System is running at this time.

Performed heating maintenance on one heat pump system. Checked all electrical, mechanical and performance of the system. Customer supplied a 4-inch media filter for replacement. Cleared and treated the drain line and washed the outdoor coil. No major issues were found and the system is operational at this time. See attached checklist for full tune-up details.

Performed heating maintenance on one heat pump system and one electric heating system. Checked all electrical, mechanical and performance of the systems. Cleared and treated the drain line and washed the outdoor coil. I found that the blower wheel on the system for the main house has dirt/mold growth on it. I also found the starter and the condenser fan motor showing signs of wear and tear. I informed the homeowner and presented options to repair. No other major issues were found, and both systems are on at this time.

Performed heating maintenance on one heat pump system. Checked all electrical, mechanical and performance of the system. Cleared and treated drain line and washed the outdoor coil. Both surge protectors are working. No major issues were found. System is on at this time. See attached checklist for full tune-up details.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. Both heat strips activated. Filter changed with customer supplied filter. Outside condenser was a little dirty, so I cleaned it. No other major issues were found and system running at time of departure. Please see attached checklist for full tune-up details.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. No major issues were found. Drain line cleared, flow tested with water and treated. Condenser coil cleaned. System sterilizer is operational. System was running at the time of departure.

Performed semiannual maintenance on one comfort heating heat pump system. Inspected all Performance, Mechanical and Safety Systems. Verified all Breathe Easy Systems are operating as designed. Changed one homeowner supplied AprilAire 310 filter. Verified everything was operating within manufacture’s specifications for operation.

Performed heat check on three systems. Checked electrical, mechanical, safety, and performance of the systems. The upstairs evaporator coil is dirty. The capacitor on the condenser unit for the office is below value. No other major issues were found. See attached checklists for full tune-up details. Drain lines were cleared and treated. Condenser coils clean. Electrical disconnects confirmed in and on, and systems were running at the time of departure.

Performed heating maintenance on one heat pump system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. No major issues were found. System is on at this time.

Performed semiannual maintenance on one split heat pump system and one mini split system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within manufacture’s specifications for operation. Everything is working at this time.

Service diagnostic found that the safety switch had tripped. The primary condensate drain line was clogged and water had backed up into the secondary tripping the switch. I cleared the drain and flow tested the drain with water. I treated the drain, and the system is now operating normally.

Installed new 5-ton Carrier heat pump system. Installed 3 new Ecobee Lite thermostats. Rebuilt and insulated condensate drain line. Added SS2 and SS3 safety float switches. Replaced secondary drain pan. Installed new filter dryer, pressure tested with dry nitrogen and pulled a vacuum on the copper line set. Removed the old zoning equipment and went back with zoning. Replaced the return and supply plenums. Installed two 4” media air filters. Cleared and treated the condensate drain line. Extended onto the return and connected it to the system. Installed the 12” damper that feeds the master bedroom. Charged system to factory specs and performed a benchmark. The system is working properly at this time.

Performed heater tune-up on three systems. Checked electrical, mechanical, safety, and performance of the systems. No major issues were found. Drain lines cleared and treated. Condenser coils clean. Electrical disconnects confirmed in and on. Systems were running at the time of departure.

Ran the condensation drain out of the attic and into a rain barrel to collect the water. Cleared the drain and checked the operation; system is working and draining properly.

Installed new indoor blower motor. Tested airflow of system to verify proper airflow was being achieved during cooling modes. Cleared out the UI controller and tested system in cooling operation. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within manufacture’s specifications for operation. Everything is working at this time.

Performed service diagnostic. Diagnostic found that the contactor on the condenser unit had fused closed. Options for repair were presented to the customer and they chose to have the contactor replaced today. I replaced the contactor and function checked the system. System was running at the time of departure.

South Side HVAC System: On arrival I inspected the outdoor unit and verified there was proper voltage being delivered to the outdoor unit; however I noticed there was no call for cooling being made outside. Went into the attic through the scuttle hole in the bedroom and found that the emergency water safety switch was tripped due to a restricted primary drain line. Cleaned and cleared the primary line and flushed out with water to verify the drain had the proper slope and all blockages were fully removed. Cleaned out and reset the water safety switch and reset the cooling system. Inspected all Performance, Mechanical and Safety Systems and verified everything was operating within manufacture’s specifications for operation. Did verify the Stage 3 Breathe Easy UV light were on and operational at time of visit. Everything is working at this time.

On arrival, I found the emergency water safety switch tripped due to a restricted condensate drain p-trap. Blew out the drain to remove the immediate restriction, cleaned out the condensate line, and then blew out the drain again to help remove any remaining drain restrictions. Flushed out the condensate line with two gallons of water to confirm the drain had the correct slope and flow to the exterior drain exit near the outdoor unit. Cleaned out any drain snot from the primary pan and nearest the condensate line port. Added in a primary pan and drain treatment which will help allow for better drainage while the AC systems is running. Reset the cooling system and inspected all Performance, Mechanical and Safety systems. Verified everything was operating within manufacture’s specifications for operation. Everything is working at this time.

Performed semiannual maintenance on two cooling systems. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within the manufacture’s specifications for operation. Both indoor systems drain lines cleared and treated. One system filter was changed. Both outside condenser refrigerant pressures are within range. No major issues were found and system running at time of departure.