Wimberley TX Heating & Air Conditioning Services

Performed cooling maintenance. Checked electrical, mechanical and performance of the system. Cleared and treated drain line and washed the condenser coil. I found the blower wheel dirty and informed the customer. He declined repairs at this time. System was left on and running.

Installed 2-ton Carrier heat pump system. Installed Ecobee Pro thermostat. Rebuilt and insulated condensate drain line. Replaced supply and return plenum and sealed with mastic air lock. Cleared and treated drain and verified operation. Installed new filter dryer, pressure tested with dry nitrogen and pulled a vacuum on the copper line set. Replaced disconnect and whip at condenser. Ran new thermostat wire. Verified system charge and operation. Replaced supply plenum for the other system. Replaced capacitor for garage system.

Performed AC tune-ups on two systems. Cleared and treated drain. Condenser coil clean. No major issues found.

Performed the AC tune-up. Cleared and treated the drain line. Condenser coil clean. No major issues were found.

Performed two AC tune-ups. Cleared and treated drain line. Condenser coils clean. On system one, I found the blower motor, wheel and housing to have build up. I also found a capacitor that was under value. On system two, no major issues were found. Presented repair options to the homeowner and they decided to have the capacitor replaced and the blower motor and wheel cleaned. Completed repairs and cycled system. Both systems are operational.

Performed semiannual maintenance on one cooling system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within the manufacture’s specifications for operation. Outside condenser refrigerant pressures are within range and condenser cleaned. Indoor system drain line cleared and treated. Noted that the outdoor system capacitor is below value. Brought this to the homeowners attention and she chose to move forward with replacement of the capacitor. No other major issues found. Repair completed and system operational.

Installed new 3.5-ton Payne condenser and new TXV. Removed piston and installed a new liquid line filter dryer. Pressure tested system with dry nitrogen and pulled a vacuum on the copper line set. Replaced disconnect and whip at outdoor system. Verified system charge is at factory spec. System is working properly at time of departure.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. Drain line cleared and treated. Condenser coil cleaned. Electrical disconnect confirmed in and on. System was running at the time of departure.

Performed semiannual maintenance on one cooling system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within the manufacture’s specifications for operation. Outdoor condenser refrigerant pressures are within range and condenser cleaned. Indoor system drain line cleared and treated. Homeowner stated that they had UV lights installed and asked that I check the indoor coil for buildup. I did check and informed the customer that everything looked great on the indoor system. No major issues were found and system running at time of departure.

Performed semiannual maintenance on one cooling system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within the manufacture’s specifications for operation. Outside condenser refrigerant pressures are within range and condenser cleaned. Indoor system drain line cleared and filters changed. No major issues were found and system running at time of departure

Performed cooling maintenance. Checked electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the condenser coil. I found that the system was slightly undercharged. I performed a leak check, and no leak was found. No other major issues were found.

Performed semiannual maintenance on one cooling system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within the manufacture’s specifications for operation. Outdoor system refrigerant pressures are within range and condenser cleaned. Indoor system drain line cleared and filter changed. No major issues were found and system running at time of departure.

Performed the AC tune-up. Cleared and treated drain line. Washed off condenser coil. No major issues found.

Built a platform for the new dehumidifier to sit on. Piped the dehumidifier drain in with the air handler condensate drain. Installed a dehumidifier control and tested to ensure proper operation of the dehumidifier. Everything is working at this time.

Performed service diagnostic. Diagnostic found that the condensate drain line was clogged. Water had backed up and tripped the safety switch. Options for repair were presented to the customer and they chose to have the drain line cleared today. Drain line was cleared and flow tested with water. Drain line was treated. System was function checked. Found that the compressor had overheated and was on a thermal lockout. I cooled the compressor down and the system was function checked again. System was running at the time of departure.

Performed service diagnostic. Diagnostic found that the capacitor on the condenser unit had failed. Options for repair were presented to the customer and they chose to have the capacitor replaced today. Capacitor was replaced. System was function checked and was running at the time of departure.

Performed the AC tune-up. Cleared and treated drain line. Washed off condenser coils. No major issues were found. System was working at completion of job.

Preformed the AC tune-up. Cleared and treated the drain line. Washed off condenser coils. No major issues found. System was working at completion of job.

Performed service diagnostic. Diagnostic found that the capacitor on the condenser unit has failed. Options for repair were presented to the customer and they chose to have the capacitor replaced. Capacitor was replaced and the system was function checked. System was running at the time of departure.

Installed new air handler. Installed new supply and return plenums. Ran new control wire for thermostat and condenser. Installed buckets and ran flex duct. Installed dehumidifier. Installed Aprilaire media filter. Ran both line sets and filled with nitrogen. Installed heat pump condenser and mini-split head and condenser. Pressure tested line set with nitrogen and pulled a vacuum on both systems. Installed Ecobee Pro thermostat. Wired in dehumidifier. Installed all supply and return grilles. Charged heat pump to factory specifications. Verified all operation and everything is operating at this time.