Wimberley TX Heating & Air Conditioning Services

AC cool check was completed for a horizontal heat pump system. Drain line was flushed and treated. Outdoor coils were cleaned. All mechanical and electrical components were checked. I did find the in rush amps to the compressor slightly elevated. I did verify the system is cooling properly before departure.

Service diagnostic found that the condensation drain line was clogged at the connection to the primary pan. This was causing water to back up and spill into the secondary pan. Options for repair were presented to the customer. She chose to have the drain line cleared and to sign up for maintenance. I cleared the condensation drain line and removed the water from the secondary pan. I then flow tested the drain line with water and treated the drain line. Clear water was observed flowing out of the drain line. The system was function tested and was cooling at the completion of service.

Performed AC cooling check on three systems. Checked the electrical, mechanical, safety, and performance of the systems. I cleared the condensation drain lines and flow tested the drains with two gallons of water. I also treated the drain lines. The air filters were replaced with client supplied filters. The condenser coils were cleaned. No major issues were found. The systems were running at the completion of service.

Service diagnostic found a burnt relay connection at the air handler heat kit which was not sending a consistent 240v through the relay. Also found the outdoor capacitor had failed on the herm side. Spoke with the homeowner and he chose to do the repairs. I removed the burnt/corroded relay at the air handler. Stripped back new clean wire and secured all relay connections. Removed the failed outdoor capacitor and secured wiring terminals connections. I did also find some build up on the HVAC drain line. I cleared the primary drain line and tested it with a gallon of water at no additional cost. After repairs were completed, I function tested the system and everything is operational at this time.

Performed AC cooling checks. Checked the electrical, mechanical, safety, and performance of the systems. I cleared the condensation drain lines and flow tested the drains with two gallons of water. I also treated the drain lines. The air filters were replaced with client supplied filters. No major issues were found. The systems were running at the completion of service.

Performed AC cooling check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filters were replaced with client supplied filters. I cleaned the condenser coil. No major issues were found. The system was running at the completion of service.

Downstairs: Installed Carrier 2 Ton straight electric system. Installed Ecobee thermostat. Replaced secondary drain pan. Installed new supply and return plenums. Re attached all existing ductwork and sealed with mastic. Rebuilt and insulated primary drain line. Installed SS2 and SS3 safety switch. Pressure tested system with nitrogen and pulled a vacuum. Upstairs: Installed Carrier 2 Ton straight electric system. Installed Ecobee thermostat. Replaced secondary drain pan. Installed new supply and return plenums. Re attached all existing ductwork and sealed with mastic. Rebuilt and insulated primary drain line. Installed SS2 and SS3 safety switch. Pressure tested system with nitrogen and pulled a vacuum. Function tested both systems. Everything is working at completion of install.

Diagnostics found the outdoor contact relay faulty and not passing voltage due to ants. This is a 23 year-old Goodman heat pump. I went over repair options and Sharon chose to replace the outdoor relay at this time. Once repairs were done, I function tested the system. The system is cooling at completion of service.

AC cool check completed on a horizontal heat pump. Drain line was flushed and treated. Outdoor coils were cleaned. All mechanical and electrical components were tested. No major issues were found. The AC system is operating within manufacturer specifications.

Diagnosed a tripped float switch caused by a severe clog in the condensate removal line. I thoroughly cleaned the primary drain using brushes, compressed nitrogen and water. I then cleaned the primary drain pan and drain line with a cleaner to kill any remaining algae. I then tested the system to make sure it was draining properly. The system is running at completion of service.

AC cool check was completed on one straight cool system and two heat pumps. All outdoor coils were cleaned. All drain lines were flushed and treated. All mechanical and electrical components were checked and found within manufacturer specifications. All three systems are cooling properly at completion of service.

Removed existing supply plenum and sections of flex duct that were dirty. Built and installed new extended supply plenum. Increased the size of every duct with metal reducers 6-8 feet from the plenum. Connected ducts to the new plenum and sealed all ductwork connections with mastic/hardcast. Hang all of the ductwork in the attic. Tested operation of system. Everything is working at completion of service.

Diagnosed a clogged drain that was sending water to the shutoff. There were five dry fit couplings on the drain that were all leaking in some capacity. I glued all of those couplings and cleared the drain. I then tested the drain with water. The system is now operational.

Replaced indoor evaporator coil. Installed new line filter dryer and pressure tested system for extensive leak check. Pulled deep vacuum and weighed in new refrigerant charge. Cleaned and treated both drain lines and verified operation. Everything is working at completion of service.

Installed 3 ton Carrier R-454B heat pump system with electric heat kit. Installed Ecobee Lite thermostat. Leveled out the ground in the crawlspace and placed new system on cinder blocks/plywood. Built and installed new return plenum and extended supply plenum. Sealed all ductwork connections with mastic/hardcast. Rebuilt primary condensation drain, added SS2 and SS3 safety switches. Cleared with CO2 and primed with water. Pressure tested system with nitrogen and pulled vacuum. Tested heating and cooling operation of new system. Everything is working at completion of install.

Installed Carrier mini split for the garage apartment. Installed wall bracket. Pressure tested system and pulled a vacuum. Installed line hide. Ran high voltage in seal tite back to the breaker panel and installed a breaker. Tested system operation. Installed 4 ton carrier R-454B heat pump system. Installed new secondary drain pan. Built and installed new return plenum and extended supply plenum. Rebuilt primary condensation drain, added SS2 and SS3 safety switches. Cleared drain with CO2 and primed with water. Installed EcoBee pro thermostat. New disconnect box and pad for the condenser. Pressure tested system with nitrogen and pulled vacuum. Tested heating and cooling operation of new system. Everything is working at completion of install.

Performed AC cooling check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. The system sterilizers and air purifier are operational. The condenser coil was cleaned. No major issues were found. The system was running at the completion of service.

Performed AC cooling check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filters were replaced with client supplied filters. The condenser coil was cleaned. No major issues were found. The system was running at the completion of service.

Diagnostics found both primary and secondary drain lines were clogged. I also found both float switches faulty, which led to water overflowing from the emergency drain pan. I presented my findings to the homeowner and she chose to replace the two float switches, remove of all water in the emergency drain pan, and flush and treat both drain lines. I installed the new float switches and removed the water from the drain pan. I then flushed and treated both drain lines. The system is cooling properly at time of departure.

Diagnostics found the in-line float switch tripping the system periodically. I went over my findings and repair options with Bob. He chose to have the drain cleared. I cleared, flushed, and treated the drain line and then function tested the system. The system is running properly at time of departure.