Wimberley TX Heating & Air Conditioning Services

Found that all three thermostats had reset to run the systems seasonally. Reinstalled them to run every time the system is to be cycled. All three systems are working at this time.

Install new UI. Salt return air filter grill and supply grill in bathroom

Perform the AC tune-up and everything is working at this time.

Perform the AC tune-up and everything is working at this time.

Look over the concerns that Mr. Jaworski had. All three of the Halos are working properly at this time. All three systems are operational. My main concern is that we do not have enough wires on the Nest for proper operation. I advise him to let me run a new thermostat wire with enough leads to power the thermostat properly before we condemn the thermostat. We will do this later this year if he continues to have issues with the thermostat.

Replace both zone dampers, zone control board, user interface and both smart sensors. Dampers are opening and closing as they should, and the system is working at this time.

I find the primary drain line to be completely clogged and shutting down the safety float switch. I also find the evaporator coil to be dirty and in need of cleaning. I present options to the customer and they choose to just have the drain cleared at this time.

Install new 2-ton Carrier Performance Series heat pump in attic. Replace drain pan, return and supply plenums, and install new line filter drier. Pressure test system for extensive leak check and pull deep vacuum. Seal all pressure points with air lock and mastic tape and rebuild primary drain. Install new Edge thermistat and charged to factory specs. Cut out scuttle access for future servicing and insulate cover.

I find the primary drain line to be completely clogged on the older downstairs unit. I gave the customer her options and she chose to have it fixed at the bronze level at this time. After re-piping the drain line with a safety float switch, I was able to clear and treat the primary drain line. Performed a system inspection and it is working at this time.

I found the system to be completely empty on R-22 refrigerant and the compressor was not running. I call the customer to inform them of their options, but they did not answer. I'm waiting for a call back to discuss options and see how they would like to proceed.

Connect Zone 3 (master bedroom). Install smart sensor in bedroom. Connect return air to system. Put in supply grilles. Need to come back and put in a 12 x 6 one-way curve blade grill in bathroom and install return air filter grill in bedroom.

I found an inoperable zoning system. The user interface would send the signal, but the board would not send the signal to the damper or the damper would stay stuck open when it finally received the call and would not close. I recommend replacing these parts: - 2 - 14" communicating dampers - 1 - Carrier Infinity control board - 1 - Carrier Infinity user interface Please see attached quote.

Replace completely depleted voltage enhancer. Check amp draws on loads and refrigerant levels. System working at completion of service.

Replace completely depleted voltage enhancer. Check amp draws on loads and refrigerant levels. System working at completion of service.

Replace completely depleted voltage enhancer. Check amp draws on loads and refrigerant levels. System working at completion of service.

Replace completely depleted voltage enhancer. Check amp draws on loads and refrigerant levels. System working at completion of service.

Sealed the supply plenum transition where it meets the unit. It looks like when we installed the system, we did not use hard cast in this area and the tape came undone. I sealed it with air lock and hard cast and there is no more air coming out right there.

Perform the AC tune-up and everything is working at this time. While performing the inspection I did find the voltage enhancer to be weak and undervalued. I gave the customer their options and they chose to have it replaced at the platinum level at this time. After replacing the voltage enhancer, voltage distributor and installing a new start assist everything is coming on and working at this time.

I found multiple issues with the 34-year-old Lennox condenser that controls the living area. I give the ranch manager their options and they decide to have the system replaced. Replacement scheduled for this Thursday July 9th.

I find the voltage enhancer to be weak and undervalued. It is supposed to be 45/5 but is reading 36.3/0.9. I also found the voltage distributor to be in poor condition and recommend replacement. I inform the customer that the plenum upstairs is falling apart and looks like the last guy out here just tried to tape it back together, but we are still leaking lots of air into the attic. I gave the customer his options and he chose to just have the voltage enhancer replaced at the basic level at this time. The condenser fan motor looks rough as well, but it is pulling 1.4 amps and is rated for 1.5. After replacing the part everything is coming on and working at this time. I did inform the customer that the system is in poor condition and will most likely have issues or need to be replaced in the very near future.