Wimberley TX Heating & Air Conditioning Services

When I arrived I found the breaker that goes to the condenser to be tripped. After taking a look at the unit and then turning the power back on the compressor was pulling locked rotor amps causing a comple failure. I gave the customer his options to replace the system and he chose to go ahead and have it replaced next Thursday. We will need to bring a 16x30 return air filter grille to add a new return.

When I arrived, I found the zone damper that controls the master bedroom to be completely seized up. I gave the customer their options and they chose to have it replaced. It will be the first part of next week before we can get the parts and replace it. The office will call to schedule once the parts arrive.

The silver tape that was sealing the Reme Halo to the plenum had separated and was leaking air. I removed the tape and cleaned the area before using a better hard cast tape to secure it. Everything is working at this time with no air loss.

Installed a new REME Halo in the main system. Removed all the moldy sheet rock in the return plenum and replaced with fresh clean duct board and sealed the entire return air chase. Cleaned the master bedroom system and condenser. Removed about 14 inches of leaves from the condenser. Checked operation of the system. We will return to clean the ducts.

Performed the AC tune-up and everything is working at this time. While performing the inspection I did find the voltage enhancer to be low on value. I gave the customer her options and she decided to wait on replacement at this time.

Replaced depleted capacitor under warranty

Replaced depleted capacitor under warranty

Replaced depleted capacitor under warranty

Replaced depleted capacitor under warranty

When I arrived, I found a complete failure of the voltage enhancer going to the blower motor. I gave the customer his options and he chose to have it replaced at the bronze level at this time. After replacing the part and turning the system back on the blower motor was making a loud whining noise. I informed the customer that the motor will be failing soon, and I could not guarantee that it would even work after I left. He said he has a new roof coming next week and he wants to hold off until it goes out. I also found the condenser fan motor bearings to be failing as well. Customer knows the 18-year-old system will need to be replaced soon but wants to hold off for now.

Installed compressor saver and purged drain line as a courtesy. Tested the system and it was working at completion of service.

Installed compressor saver and purged drain line as a courtesy. Tested the system and it was working at completion of service.

Installed compressor saver and purged drain line as a courtesy. Tested the system and it was working at completion of service.

Installed compressor saver and purged drain line as a courtesy. Tested the system and it was working at completion of service.

When I arrived, I found the primary drain line to be completely clogged and draining water on the floor. I gave the customer his options and he chose to have it repaired at the silver level. After clearing and treating the primary drain line I also installed a safety float into the secondary drain port to prevent it from overflowing again. Everything is working at this time.

Installed new Carrier system in attic. Added new drain pan and supply plenums. Sealed all pressure points with air lock and mastic tape. Installed new Carrier Edge thermostat and rebuilt primary and secondary drain. System charged to factory specs and working at this time.

Installed new Carrier system in attic. Added new drain pan and supply plenums. Sealed all pressure points with air lock and mastic tape. Installed new Carrier Edge thermostat and rebuilt primary and secondary drain. System charged to factory specs and working at this time.

Installed new Carrier system in attic. Added new drain pan and supply plenums. Sealed all pressure points with air lock and mastic tape. Installed new Carrier Edge thermostat and rebuilt primary and secondary drain. System charged to factory specs and working at this time.

Installed new Carrier system in attic. Added new drain pan and supply plenums. Sealed all pressure points with air lock and mastic tape. Installed new Carrier Edge thermostat and rebuilt primary and secondary drain. System charged to factory specs and working at this time.

When I arrived, I found that the thermostat was not sending 24 volts to the reversing valve the way it was supposed to when calling for cool. I replaced the thermostat under parts and labor warranty. Everything is coming on and working at this time.