Wimberley TX Heating & Air Conditioning Services

Performed a/c tune-up on two Carrier Infinity heat pump systems. Checked the electrical, mechanical and performance systems of the units. Cleared, cleaned, flushed and treated the drain line. Cleaned the exterior of the air handler and washed the outdoor coil. Did find some rust spots on the master bedroom secondary drain pan. No other issues were found. All air purifiers and surge protection devices are working. I function tested the mini split and tested the drain line as well. All systems are operational at this time.

Installed Carrier 3 ton heat pump. Installed plywood overlay. Transitioned to existing duct work. Rebuilt primary drain, tested and cleared the drain. Pressure tested system and pulled a vacuum. Replaced disconnect and whip. Ran low voltage in 1/2 inch seal tite. Tested system operation. Everything is working at completion of service.

Built and installed new return plenum and extended supply plenum. Cut out sections of flex duct that were dirty. Spliced on new sections of flex duct. Increased the size of the main return to a 20x30 filter grill and 18 inch flex with new plenum. Cut in a new return to the son’s bedroom. Ran new 8 inch flex. Sealed all ductwork connections with mastic / hardcast. Everything is working at completion of service

Performed a/c tune-up on a Carrier heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. Secured outdoor compressor wiring and washed the outdoor coil. I did find possible signs of rodents in the attic and the compressor is doing high in rush amps No other issues were found. The system is operational.

Cut out and removed existing primary drain line. Installed new primary condensation drain up to the exterior wall, insulated the entire run. Rebuilt connection at the evaporator coil with a new p-trap. Poured a gallon of water down the new drain to ensure proper operation. Raised the back of the secondary drain pan with rubber pads and plumbing strap so that it is now level. Everything is working at completion of service.

Service diagnostic found that the condensation drain line was clogged. Water had backed up into the safety switch and shut down the system. Options for repair were presented to the homeowner. They chose to have the condensation drain line cleared and to sign up for maintenance. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. I function tested the system and the system was running at the completion of service.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with water. I also treated the drain line. The air filter was clean and had been recently replaced by the homeowner. No major issues were found. The system was running at the completion of service.

Performed heat check on two systems. Checked the electrical, mechanical, safety, and performance of the systems. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filters were clean and had been replaced by the homeowner before my arrival. No major issues were found. The systems were running at completion of service.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filters were replaced with a client supplied filter. No major issues were found. The system was running at the completion of service

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. I did find that the compressor was drawing high amps on startup of the system. Max LRA for the system is 67.8 amps and I was reading 70.3 amps. The system was running at the completion of service.

Pumped system down and removed old coil. Installed new coil and pressure tested lineset. Rebuilt primary drain line and cleared the drain. Pulled a vacuum on the copper lineset and added additional refrigerant to meet manufacturer specifications. Tested system operation. Everything is working at this time.

Performed heat check on two systems. Checked the electrical, mechanical, safety, and performance of the systems. I cleared the condensation drain lines and flow tested the drains with two gallons of water. I also treated the drain lines. The air filters were replaced with client supplied filters. No major issues were found. The systems were running at the completion of service.

Performed heater tune-up on two Carrier infinity heat pump systems. Checked the electrical, mechanical and performance systems of the units. Cleared, cleaned, flushed and treated the drain lines and cleaned the exterior of the air handlers. I did find the homeowner had both a 1 inch and 4 inch filter in the system. Replaced both 4-inch filters with client supplied filters and removed the 1 inch filters. Also found the UV light for the master bedroom system has burnt out. No other issues were found. Both systems are operational at this time.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filters were clean and had been recently replaced by the homeowner. No major issues were found. The system was running at the completion of service.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I replaced the air filter with a client supplied filter. The condensation drain line was frozen. I did treat the drain line. Surge protectors for the system are operational. No major issues were found. The system was running at the completion of service.

Performed heater tune-ups on an Amana and an American Standard heat pump system. Checked the electrical, mechanical and performance systems of the units. Cleared, cleaned, flushed and treated the drain lines. Spoke with the homeowner about the age and shape of the systems. No other issues were found. Both systems are operational at this time.

Heating tune-up completed on all three heat pump systems. Drain lines were flushed and treated. All outdoor coils were cleaned. The air filters were changed. All electrical and mechanical components were checked. The systems were running at completion of service.

Removed existing strap and installed custom wood supports to stabilize and level the detached supply plenum. Resealed it with mastic and gypsum tape along with return air connection. Sealed all straws and points of intrusion with silicone and cork tape. Removed and cleaned blower assembly as well as the indoor cabinet. Cleaned coil in place and treated and tested drainage system. Verified operation and checked outdoor cap. Everything is working at completion of service.

Removed all existing ductboard plenums. Removed blower motor and cleaned the wheel/housing. Cleaned interior of the air handler and the primary drain pan. Built and installed new return plenum. Built and installed new elbowed trunk lines for the supply side of the system. Reattached all existing flex duct to the new plenums. Sealed all connections with mastic / hardcast. Sealed all buckets to the Sheetrock. Installed two Solaris UV lights and power supply pack. Installed new secondary drain pan. Rebuilt primary condensation drain. Cleared with CO2 and primed trap with water. Tested operation of system and new UV lights. Everything is working at completion of service.

Installed Santa Fe 100 pint dehumidifier on newly built platform above the air handler with new drain pan. Ran a new 12 inch flex return from each filter box to the plenum, 2 runs in total. Built condensation drain for the dehumidifier tying into the system’s primary with ball valves. Cleared primary drain with CO2 and primed both traps with water. Tested operation of dehumidifier and system. Everything is working at completion of install.