Wimberley TX Heating & Air Conditioning Services

Performed AC cool checks on three systems. Checked the electrical, mechanical, safety, and performance of the systems. I cleared the condensation drain lines and flow tested the drains with two gallons of water. I also treated the drain lines. The air filters were replaced with client supplied filters. I cleaned the condenser coils. No major issues were found. The systems were running at the completion of service.

Performed AC cool check on two systems. Checked the electrical, mechanical, safety, and performance of the systems. I cleared the condensation drain lines and flow tested the drains with two gallons of water. I also treated the drain lines. I cleaned the condenser coils. No major issues were found. Both systems were running at the completion of service.

Installed Carrier 5 ton straight electric heat pump system. Installed Ecobee pro thermostat. Laid down new plywood in the attic for the system to sit on. Installed new secondary drain pan. Built and installed new trunk line supply plenum. Built and installed new return plenum with offset to match up with system. Installed new 12x12 return filter grill in the library, with new 8 inch flex running to the return plenum. Rebuilt primary condensation drain, installed new SS2 and SS3 safety switches. Cleared primary drain with CO2 and primed trap with water. Sealed all ductwork connections with mastic/hardcast. Pressure tested system with nitrogen and pulled vacuum. Installed new disconnect box and wiring for the condenser. Charged AC with R-454B refrigerant. Tested heating and cooling operation. Everything is working at completion of install.

Installed Carrier air handler. Installed new Ecobee thermostat. Installed new supply and return air plenums and sealed all connections with mastic. Replaced secondary drain pan. Rebuilt and insulated primary drain line, installed safety switches and cleared drain. Replaced disconnect and whip at outdoor unit. Charged unit to meet manufacturer specifications. Everything is working at completion of service.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. I cleaned the condenser coil. No major issues were found. The system was running at the completion of service.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. Condenser coil was cleaned. No major issues were found. The system was running at the completion of service.

Performed a/c tune-up on a Carrier heat pump system. Cleared, cleaned, flushed and treated the drain line and washed the outdoor coil. I did find the return side of the system has high static at .4. and is not allowing 100% airflow across the system. I went over my findings with homeowner. No other issues were found. The system is operational at this time.

AC cooling tune-up completed on one vertical Carrier heat pump. Drain line was flushed and treated. Condenser coils were cleaned. I found the current charge on the outside torque booster is right at where we would consider replacement. No other major issues were found. The system was cooling at time of departure.

Performed A/C tune-up on a Carrier straight cool system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and replaced the return air filters. Verified the outdoor compressor wiring is secure and washed the outdoor coil. No major issues were found. All surge protection devices are working. The system is operational at this time.

Performed A/C tune-up on a Bryant heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. Replaced the return air filters with client supplied filters. Verified outdoor compressor wiring is secure and washed the outdoor coil. No major issues were found. The UV light at the air handler is working. The system is operational at this time.

Performed A/C tune-ups on one American Standard system & one Amana heat pump system. Checked the electrical, mechanical and performance systems of the units. Cleared, cleaned, flushed and treated the drain lines and washed both outdoor coils. On the guest house system I found some biological growth on the coil and blower wheel. At the outdoor unit I found the starter is pitted and the fan motor is leaking oil. On the main house system I found the indoor coil is extremely clogged with biological growth and very rusted. The air flow across the coil is low due to the growth which could cause the system to freeze over if it runs long enough. There is also some growth on the blower wheel and there is no water safety switch on the system. I spoke with the homeowner about my findings Both systems are operational at this time.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filters were clean and had been replaced by the homeowner. I cleaned the condenser coil. Surge protectors are operational. No major issues were found. The system was running at the completion of service.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. I cleaned the condenser coil. No major issues were found. The system was running at the completion of service.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The filter was clean and had been recently replaced by the homeowner. I cleaned the condenser coil. The capacitor for the blower motor was below value and the condenser fan motor showed signs of overheating. Options for repair were presented to the homeowner and she chose to have the blower motor capacitor replaced today. I replaced the capacitor and function tested the system. The system was running at the completion of service.

Performed an AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a customer supplied filter. The contactor on the condenser unit is burnt and pitted. Options for repair were presented to the homeowners and they chose to have the contactor replaced. I replaced the contactor and function tested the system. The system was running at the completion of service. No other major issues found

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a customer supplied filter. I cleaned the condenser coil. No major issues were found. The system was running at the completion of service.

Service diagnostic found that the condensation drain line was clogged. Water had backed up into the secondary drain line and tripped the safety switch. Options for repair were presented to the homeowner, and they chose to have the drain line cleared. I cleared the condensation drain line and flow tested the drain line with two gallons of water. I also treated the drain line. I function tested the system and the system was cooling.

Performed an AC cool check. Checked electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was clean as it had been recently replaced by the customer. I cleaned the condenser coil. The system was running at the completion of service.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. Clear water was observed flowing out of the drain line. I also treated the drain line. The air filter was replaced with a customer supplied filter. The drain line is piped without a vent to help with water flow and has a trap made from 90-degree PVC connections. The drain is draining now but has had issues in the past. Some mold/mildew was found growing inside the air handler. No other major issues found.

Performed AC cool check on two systems. Checked electrical, mechanical, safety, and performance of the systems. I cleared the condensation drain lines and flow tested the drain with water. Clear water was observed flowing out of the drain lines. I also treated the drain lines. Condenser coils were cleaned. No major issues were found. The systems were running at the completion of service.