HVAC Service In Buda, TX

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. The blower wheel is clean. The blower motor capacitor is below value. Wiring is tight and in good condition. Condenser coil clean. The contactor and condenser fan motor are in good condition. Condenser capacitor is within value. Refrigerant charge is within factory specifications. No other major issues found. Options for repair were presented to customer and he chose to have the blower motor capacitor replaced today. I replaced the blower motor capacitor and function checked the system. System was running at the time of departure.

Performed a whole house duct cleaning. During the cleaning we found a duct that had bacteria growing. We let the homeowner know what we found and recommended it be replaced; the homeowner agreed. We replaced the duct. We also performed a drain clearing and vacuuming out the secondary drain pan that was full of water. We treated the drain line once it was cleared.

HVAC System Repairs: Upon evaluating the client's HVAC system, I noted frequent short cycling, which not only decreased efficiency but also posed a risk of compressor damage. To rectify this, I fine-tuned thermostat settings, replaced dirty air filters, and ensured unimpeded airflow. These adjustments optimized cycling intervals, preserving system components and maximizing performance.

Attic Insulation Installation: Enhancing energy efficiency, I upgraded attic insulation to prevent heat loss and maintain comfortable temperatures year-round. By installing high-quality insulation materials, I helped the homeowner save on energy costs while maximizing indoor comfort.

Air Conditioning System Repairs: During my assessment of the client's HVAC system, I discovered a malfunctioning defrost control board, causing improper defrost cycles and reduced efficiency. To rectify this issue, I replaced the faulty defrost control board, ensuring accurate defrost cycles and optimizing the overall performance of the system.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. Filters were replaced with customer supplied filters. The blower wheel is clean, and the blower motor capacitor is within value. The wiring is tight and in good condition. Condenser coil clean. Condenser capacitor is depleting and below factory specifications. Condenser fan motor is showing signs of overheating. The refrigerant charge is within spec. No other major issues found.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. Return and supply plenums are clean. The blower wheel is also clean. The drain line was cleared and treated. The wiring is tight and in good condition. Surge protection for the furnace and condenser unit are operational. The condenser fan motor is in good condition and refrigerant charge is within factory specifications. Condenser coil clean. The system was running at the time of departure.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. Return and supply plenums are clean. The blower wheel is also clean. The drain line was cleared and treated. The wiring is tight and in good condition. Surge protection for the furnace and condenser unit are operational. The condenser fan motor is in good condition and refrigerant charge is within factory specifications. Condenser coil clean. The system was running at the time of departure.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. Return and supply plenums are clean. The blower wheel is also clean. The wiring is tight and in good condition. Both zone dampers are operational. Filters were replaced with customer supplied filters. Condenser coil clean. Condenser capacitor and fan motor are in good condition. The contactor is also in good condition. Refrigerant charge is in range for factory specifications. Surge protection for the furnace and the condenser are both operational. System was running at the time of departure.

On arrival, I turned the thermostat to cooling mode and found that the outdoor heat pump would not turn on. I checked the emergency water safety switch and found it to have tripped due to a clog in the primary drain line. Flushed and treated the primary drain system. Verified system was operating within manufacture’s specifications for operation. Everything is working at this time.

Installed new Stage 2, Stage 3 and Stage 4 Breathe Easy Systems. Installed new outdoor condenser fan motor. Verified operation of all systems and also verified new Breathe Easy systems were on and operating as designed. Everything is working at this time.

Installed a Carrier heat pump system. Installed Ecobee thermostat. Installed return and supply plenums and sealed all connections with mastic. Replaced secondary drain pan. Rebuilt and insulated primary and secondary drain lines. Cleared, treated, and verified drain operation. Installed surge protectors on both indoor and outdoor units. Replaced disconnect and whip at outdoor unit. Ran low voltage in 1/2-inch Seal-Tite. Replaced thermostat for other system in house. Fixed multiple locations of outer flex liner and suction line insulation that had been chewed up. Verified system charge was at manufacturers specifications. System operational.

I arrived to find both systems off and not running. I made sure to rinse out both coils and also clear both drains. I also tested and treated drains. During my evaluation of the systems, I discovered that the downstairs system float switches have both failed. I also found that the contactors on the outdoor units are pitted and charred. I brought all of this to the attention of Barry and Cathi and gave them a few options. They elected to talk it over and get back with us when they’re ready.

I arrived to find both systems off and not running. I made sure to rinse out both coils and also clear both drains. I also tested and treated drains. During my evaluation of the systems, I discovered that the downstairs system float switches have both failed. I also found that the contactors on the outdoor units are pitted and charred. I brought all of this to the attention of Barry and Cathi and gave them a few options. They elected to talk it over and get back with us when they’re ready.

I arrived to find both systems off and not running. I made sure to rinse out both coils and also clear both drains. I also tested and treated drains. During my evaluation of the systems, I discovered that the downstairs system float switches have both failed. I also found that the contactors on the outdoor units are pitted and charred. I brought all of this to the attention of Barry and Cathi and gave them a few options. They elected to talk it over and get back with us when they’re ready.

I arrived to find both systems off and not running. I made sure to rinse out both coils and also clear both drains. I also tested and treated drains. During my evaluation of the systems, I discovered that the downstairs system float switches have both failed. I also found that the contactors on the outdoor units are pitted and charred. I brought all of this to the attention of Barry and Cathi and gave them a few options. They elected to talk it over and get back with us when they’re ready.

Performed semiannual maintenance on one straight electric cooling system. Inspected all Performance, Mechanical and Safety Systems. Did verify everything was operating within manufacture’s specifications for operation. Customer mentioned that her heater was not operating. I tested all safety limit switches and furnace controls, reset the furnace and cycled the heater multiple times. Verified everything was operating as designed.

Single system cooling check completed. Drain lines have been cleared and treated. Coils are clean. All electrical within manufacture specs. No major issues found, and the system is operating properly at this time.

Single system cooling check completed. Both coils are clean and the drain line has been cleared and treated. I found that the blower motor and housing is dirty, and the condenser fan motor is showing signs of overheating. No other major issues found

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. Drain line was cleared and treated. The blower wheel is clean. The wiring is tight and in good condition. The condenser fan motor is in good condition and so is the contactor. The condenser capacitor is within value and the condenser coil is clean. No major issues were found.