HVAC Service In Buda, TX

Performed service diagnostic. Diagnostic found that the disconnect to the condenser unit is faulty. Options for repair were presented to customer and they chose to have the disconnect replaced today. Repair was completed. System was function checked. System was running at the time of departure.

Performed semiannual maintenance on one heat pump heating system. Homeowner changed his 24x24x1 filter prior to our arrival. Inspected all Performance, Mechanical and Safety Systems. Homeowner mentioned his unit would turn off automatically about every 20 minutes. Found the low voltage control wiring and thermostat programming to be incorrect causing the thermostat to think the system was a 2 Stage with Dual Fuel heating system. Corrected wiring and verified operation. Everything is working at this time. Please see attached checklist for full tune-up details.

Performed semiannual maintenance on one gas furnace heating system. Inspected all Performance, Mechanical and Safety Systems. Did note the combustion exhaust motor beginning to over amp slightly showing signs of wear and tear. This does need to be monitored or replaced soon to ensure continuous use of the heating system for home. Verified everything else was operating within the manufacture’s specifications for operation.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. No major issues were found. Drain line cleared and treated. Condenser coil clean. Electrical disconnect confirmed in and on. System was running at the time of departure.

Trip 1 - Performed service diagnostic. Diagnostic found that the blower motor has failed. Blower motor capacitor is also below value. Options for repair were presented to customer and they chose to have both components replaced. Motor has been ordered and we will return to complete repairs once received. Supply house said it will be in possibly later this week but most likely mid-next week due to the holidays. Our office will contact the customer to schedule once motor is received. Trip 2 - Replaced indoor blower motor and battery capacitor. Verified system operation in heating and in cooling. System operating at this time.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. No major issues were found. Drain line was cleared and treated. Condenser coil cleaned. Electrical disconnect confirmed in and on. System was running at the time of departure.

Performed semiannual maintenance on one gas furnace heating system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within the manufacture’s specifications for operation. Everything is working at this time. Please see attached checklist for full tune-up details.

Installed new 2.5-ton straight AC system. Rebuilt and insulated condensate drain line. Added SS-2 and SS-3 safety float switches. Replaced secondary drain pan. Installed new filter dryer, pressure tested with dry nitrogen and pulled a vacuum on copper line set. Built a transition to existing supply and return plenums and sealed with mastic airlock. Added 1/2-inch seal tight to low voltage wire on the condenser. Charged system to factory spec. System is working properly at time of departure.

Found the primary drain line backed up, intermittently tripping the emergency float switch. Removed p-trap, flushed drain, and treated with a pan & drain treatment. Also installed a union for ease of cleaning for future use. Everything is working at this time.

Performed semiannual maintenance on one heat pump heating system. Inspected all Performance, Mechanical and Safety Systems. Changed two homeowner supplied filters and flushed and treated the primary drain system. Found everything to be operating within manufacture’s specifications for operation.

Performed semiannual maintenance on two heat pump heating systems. Inspected all Performance, Mechanical and Safety Systems. Found everything to be operating within the manufacture’s specifications for operation.

Trip 1 - On arrival, the system was reading an error code 33 for “ignition proving fault”. Upon further inspection I found that the gas valve has failed intermittently. Verified proper voltage to gas valve and verified inlet pressure was within range. Gas valve is failing to open up during sequence. Ordered new gas valve and will return to complete repairs once received. Trip 2 - Replaced gas valve and reinstalled gas pipe. Once that was done, I leak checked all my connections. Turned the system on and checked operation. System is working at completion of service.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. Blower motor capacitor was below value. No other major issues were found. Drain line cleared and treated. Condenser coil cleaned. Electrical disconnect confirmed in and on. Gas valve and manifold confirmed on. Options for repair were presented to the customer and they chose to have the capacitor replaced and renew maintenance. Repair was completed. System was function checked and returned to the customer’s desired temperature. Please see attached checklist for full tune-up details.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. Evaporator coil had some dirt and buildup on the underside of the coil. Blower wheel was dirty and is starting to accumulate buildup as well. Some mold/mildew is developing on the wiring harness for the blower fan. No other major issues were found. Drain line cleared and treated. Condenser coil cleaned.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. Inducer motor was pulling high amps. No other major issues were found. Drain line cleared and treated. Condenser coil cleaned. Electrical disconnect confirmed in and on. Gas valve and manifold confirmed on. I contacted the supply house for availability of the motor, and it is on backorder. Customer chose to wait on replacement of the motor due to availability issues. System was running at the time of departure.

Performed semiannual maintenance on one gas furnace heating system. Inspected all Performance, Mechanical and Safety Systems. Found everything to be operating within manufacture’s specifications for operation. Everything is working at this time.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. No major issues found. Drain line cleared and treated. Condenser coil cleaned. Electrical disconnect confirmed in and on. Gas valve and manifold confirmed on. System was running at the time of departure.

Performed semiannual maintenance on one heat pump heating system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within the manufacture’s specifications for operation. The four-inch media filter that was currently in place did have dust build up, however at time of the visit the homeowner did not have a replacement filter. Let him know to go ahead and order a new set of filters to replace the one currently installed. Everything is working at this time and all surge protectors and ultra-violet lights are currently operational. Please see attached checklist for full tune-up details.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. No major issues were found. Electrical heat strips on and functioning. Drain line cleared and treated. Condenser coil cleaned. Electrical disconnect confirmed in and on. System was running at the time of departure.

Performed semiannual maintenance on one gas furnace and one mini split. Inspected all Performance, Mechanical and Safety Systems. Did find that the furnace system’s drain line is clogged causing the emergency water safety switch to be activated. Clean and cleared drain line and verified system operation. Whole Home Air Purifier is working and operational at time of visit. Did note the inverter heat pump did not have a surge protection device installed putting the system at risk to electrical surges. Recommend installing surge protection on unit. Everything is working at this time. Changed one 24x24x4 filter. Please see attached checklists for full tune-up details.