Kyle TX Heating & Air Conditioning Services

I made sure to rinse out the condenser. During my investigation of the system, I discovered the following: the drain line is clogged, the system has the discontinued and flawed electronic float switch, the contactor is pitted and charred, and the blower motor is leaking oil. The customer elected to have me install two new float switches and renew her maintenance plan for now. I also cleared the drain and completed the semiannual maintenance. The system is in working order.

Performed cooling maintenance on two systems. Checked electrical, mechanical and performance of both systems. Cleared and treated the drain lines and washed both outdoor coils. Customer supplied filters for replacement. No major issues were found. Both systems are operational at this time.

Performed service diagnostic. Diagnostic found that the contactor in the condenser unit has failed. Options for repair were presented to the customer and he chose to have the contractor replaced. I replaced the contactor and function checked the system. The system was running at the time of departure.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The air handler, evaporator coil and blower wheel are dirty. Drain line was cleared and treated. The condenser fan motor is leaking lubricant, and the condenser contactor is burnt. Capacitor for the condenser unit is within value and condenser coil clean. Options for repair were presented to the customer and he chose to have the condenser fan motor and contactor replaced, the air handler/evaporator coil and blower wheel cleaned and to have system sterilizers installed. I replaced the condenser fan motor and contactor on the condenser unit. I cleaned the blower wheel, air handler and evaporator coil and then installed system sterilizers. System was function checked and was running at the time of departure.

Pulled the evaporator coil and replaced both primary drain pans. Rebuilt the drain line and checked for proper operation. Removed the water that was in the secondary drain pan. Checked the operation of the system and it is working properly at this time.

I made sure to clear the drain and also rinse out the condenser coil. I checked over the system and found everything in great shape. I did find that one of the caps on the drain pan had snapped off, so I removed the threaded section and installed a cap in its place. I made sure to seal it with leak lock. Not only was it losing air there it would’ve also become a problem had the drain ever clogged up. Both the indoor and outdoor motors are operational. The capacitor is within range. The contactor looks good. The refrigerant charge is proper as well. No recommendations were made at this time. System is in working order at completion of appointment.

I made sure to clear the drain and also rinse out the condenser coil. I checked over the system and found everything in great shape. I did find that one of the caps on the drain pan had snapped off, so I removed the threaded section and installed a cap in its place. I made sure to seal it with leak lock. Not only was it losing air there it would’ve also become a problem had the drain ever clogged up. Both the indoor and outdoor motors are operational. The capacitor is within range. The contactor looks good. The refrigerant charge is proper as well. No recommendations were made at this time. System is in working order at completion of appointment.

I made sure to clear the drain and also rinse out the condenser coil. I checked over the system and found everything in great shape. I did find that one of the caps on the drain pan had snapped off, so I removed the threaded section and installed a cap in its place. I made sure to seal it with leak lock. Not only was it losing air there it would’ve also become a problem had the drain ever clogged up. Both the indoor and outdoor motors are operational. The capacitor is within range. The contactor looks good. The refrigerant charge is proper as well. No recommendations were made at this time. System is in working order at completion of appointment.

I made sure to clear the drain and also rinse out the condenser coil. I checked over the system and found everything in great shape. I did find that one of the caps on the drain pan had snapped off, so I removed the threaded section and installed a cap in its place. I made sure to seal it with leak lock. Not only was it losing air there it would’ve also become a problem had the drain ever clogged up. Both the indoor and outdoor motors are operational. The capacitor is within range. The contactor looks good. The refrigerant charge is proper as well. No recommendations were made at this time. System is in working order at completion of appointment.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. The blower wheel is clean and blower motor capacitor is within value. Control wiring was tightened. Return plenum is clean. The condenser fan motor is in good condition. Surge protection is operational. Condenser coil cleaned. No major issues were found, and the system was running at the time of departure.

Performed the AC cool check. Checked electrical, mechanical, safety, and performance of the system. The evaporator coil and primary pan have some mold growth on them. The blower wheel is clean. The electrical wiring is tight and in good condition. Surge protector for the air handler is operational. The drain line was cleared and treated. Condenser coil clean. Surge protection for the condenser is operational. Condenser capacitor is within value and the contactor is in good condition. No other major issues were found. I showed the mold growth to the customer and wiped off the visible mold I could reach.

Installed 4-ton Carrier gas system. Installed Ecobee thermostat. Installed New supply and return plenums and sealed all connections with mastic. Replaced secondary drain pan. Rebuilt and insulated primary and secondary drain lines. Installed SS2 and SS3 safety float switches. Cleared and verified drain operation. Replaced disconnect and whip for outdoor condensing unit. Ran the low voltage wire in 1/2-inch Seal-Tite. Pressure tested and pulled a vacuum on the copper line set. Weighed in charge to meet manufacturer specifications.

Performed cooling maintenance on one straight cool system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. I found that the system is slightly low on refrigerant. I spoke to the customer, and he chose to have refrigerant added today. I added 14 ounces of refrigerant and performed a leak check on the system. I was not able to find a leak on the system. No other major issues were found, and the system is operational at this time.

Performed cooling maintenance on a straight cool system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. Filters were replaced by the customer before my arrival. Both surge protectors are on and working. No major issues were found, and the system is operational at this time.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. Replaced Aprilaire media filter. Found the system to be low on refrigerant. I performed a leak check and found a leak in the evaporator coil. No other major issues were found. Options for repair were presented to the customer and they chose to have refrigerant added today. I added 2.5 lbs of R-410A refrigerant and the system was running at the time of departure.