Kyle TX Heating & Air Conditioning Services

Gas valve at the furnace is shut off and red tagged saying the furnace would not light. Check of the system found that the flame sensor was burnt and wouldn’t reliably detect the ignition when the furnace started. Options for repair were presented to the customer and she chose to have the flame sensor replaced today. I replaced the flame sensor and performed a maintenance check on the furnace. Checked electrical, mechanical, safety, and performance of the system. No other major issues were found. System was set to customer’s desired temperature. System was running at the time of departure. See attached checklist for full tune-up details.

On arrival, I spoke with the homeowner and she said when they tried to turn on their AC nothing happened. Began troubleshooting and I found that the indoor control voltage fuse has failed. I went to the outdoor condenser and found that the relay starter coil was directly shorted. Installed new starter and new wire terminal connections. Reset the system and tested all modes. Verified everything was operating within manufacture’s specifications for operation. Everything is working at this time.

Performed semiannual maintenance on one heat pump heating system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within manufacture’s specifications for operation.

Performed heating maintenance on one furnace system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line. The customer did not have filters for replacement. He said he had just ordered them and will replace them as soon as he gets them. I also talked to the customer about adding a water safety switch on the secondary drain line to prevent overflow into the emergency drain pan. He declined repairs at this time. No other major issues were found, and the system is operational at this time. See attached checklist for full tune-up details.

Performed heater check on a Trane heat pump. Checked electrical, mechanical, safety, and performance of the system. Drain line was cleared and treated. Heat strips on the heat kit are operational. Air handler, blower wheel and evaporator coil are all clean. Filter was dirty but the customer did not have a replacement, so I let them know to get a new one ASAP. Condenser fan motor is in good condition. Condenser capacitor is in value. No major issues were found, and the system was running at the time of departure. See attached checklist for full tune-up details.

Performed heating maintenance on one furnace system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and the customer supplied a filter for replacement. I found that the system does not have a water safety switch. I informed the customer and presented options for repair; she declined repairs at this time. No other major issues were found, and the system is operational at this time. See attached checklist for full tune-up details.

While replacing the condenser motor, I also cleaned the inside of the system with coil cleaner. Once everything was put back together, I wiped down the entire system and applied UV Protectant. I then checked operation of the system and everything is currently working at this time.

Installed new 3-ton Carrier heat pump system. Installed new Ecobee Pro thermostat. Rebuilt and insulated condensate drain line. Added SS2 safety float switch. Installed new filter dryer, pressure tested with dry nitrogen and pulled a vacuum on the copper line set. Replaced the condenser pad. Replaced the disconnect and ran the low voltage in Seal-Tite. Added a new 20x20 filter base. Replaced the supply plenum and sealed it with a mastic sealant. Charged system to factory specs and performed a benchmark of the system. System is working properly at time of departure.

Performed heating maintenance on one heat pump system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. The condenser fan motor is showing signs of wear and tear. I informed the customer and presented options for repair. He chose to have the fan motor replaced at this time. I replaced the motor and cycled power at the thermostat. No other major issues were found, and the system is working at this time. See attached checklist for full tune-up details.

Performed heating maintenance on one furnace system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line. Filters were replaced by the customer recently and still in good condition. I did inform the customer that the furnace is 23 years old and they should start planning for replacement soon. No major issues were found, and the system is operational at this time. See attached checklist for full tune-up details.

Performed heater check on a Carrier gas furnace. Checked electrical, mechanical, safety, and performance of the system. Drain line was cleared and treated. Return and supply plenums are clean. Blower wheel and air handler are also clean. Igniter is operational and within value. Flame sensor was cleaned. Inducer motor is running at normal amperage. The dampers for both zones of the house are operational. No major issues were found, and the system was running at the time of departure. See attached checklist for full tune-up details.

Performed heater check on a Carrier gas furnace. Checked electrical, mechanical, safety, and performance of the system. Return and supply ducts are clean. Air handler and blower wheel are also both clean. Drain line was cleared, flow tested with water and treated. Blower motor capacitor is within value. Flame sensor was cleaned. Igniter is within value and operational. Inducer motor is operational and drawing normal amperage. No major issues were found, and the system was running at the time of departure. See attached checklist for full tune-up details.

Installed new 2.5-ton Carrier heat pump system. Installed new Honeywell T6 thermostat. Rebuilt and insulated condensate drain line. Added SS2 and SS3 safety float switches. Replaced secondary drain pan. Installed new filter dryer, pressure tested with dry nitrogen and pulled a vacuum on the copper line set. Replaced both supply and return plenums and sealed with a mastic airlock. Replaced the disconnect and whip to the condenser.

I installed a universal condenser fan motor, and our Stage 4 Breathe Easy Package. After I completed the work, I cycled power at the thermostat and confirmed everything was operational.

Performed heater check on a Carrier gas furnace. Checked electrical, mechanical, safety, and performance of the system. Return and supply plenums are clean. Blower wheel is also clean. Blower motor capacitor is within value. Drain line was cleared and treated. Igniter is operational and within value. Flame sensor was cleaned. Inducer motor is running at normal amps. No major issues were found, and the system was running at the time of departure. See attached checklist for full tune-up details.