Kyle TX Heating & Air Conditioning Services

Performed heater maintenance on one heat pump system. Checked electrical, mechanical, safety, and performance of the system. Heat strip activated. Filters were clean and recently changed by homeowner before arrival. During my maintenance, I noticed a large amount of rust and buildup on the blower wheel as well as the coil. Brought these findings to homeowners’ attention and informed him that due to the age of the system, as well as system running off of R-22, it would be best to replace the system. He would like to meet with a Project Manager to discuss full system replacement. Our office will reach out to schedule an appointment. No other major issues were found and the system was running a time of departure. See attached checklist for full tune-up details.

Installed new 3-ton Carrier furnace system. Installed new Ecobee Lite thermostat. Rebuilt and insulated condensate drain line. Added SS2 safety float switch. Installed new filter dryer, pressure tested with dry nitrogen and pulled a vacuum on copper line set. Ran the low voltage in Seal-Tite. Put down a plywood overlay. Built a transition to existing supply plenum and sealed with a mastic airlock.

Performed heater check on an electric down flow system. Checked electrical, mechanical, safety, and performance of the system. Air handler, blower wheel and coil are all clean. Blower motor capacitor is within value. Electrical heat strips are operational. Drain line cleared and treated. System was running at the time of departure. No major issues found. See attached checklist for full tune-up details.

Performed heater maintenance on one gas furnace. Checked electrical, mechanical, safety, and performance of the system. Flame ignition achieved and flame sensor cleaned. Filters were clean and recently changed by homeowner before arrival. I noticed some buildup on the blower wheel on the indoor system. I also noticed that the capacitor on the outdoor condenser was starting to deplete. Brought my findings to homeowner and he decided to move forward with both repairs. Pulled and cleaned the blower wheel and replaced the capacitor on the condenser. No other major issues were found and the system was running at time of departure. Gas valve confirmed on. See attached checklist for full tune-up details.

Performed heater check on a Carrier gas furnace. Checked electrical, mechanical, safety, and performance of the system. Air handler and blower wheel are clean. Electrical connections were tightened. Blower motor capacitor is within value. Drain line was cleared and treated. Igniter is operational. Flame sensor was cleaned. Inducer motor is operational and drawing normal amps. System is fully functional, and no major issues were found. See attached checklist for full tune-up details.

Performed heat maintenance on one gas furnace. Checked electrical, mechanical, safety, and performance of the system. Flame ignition achieved and flame sensor cleaned. Filter was clean as it was recently changed by the homeowner before arrival. Blower wheel clean and drain clear. No major issues were found and the system is running at time of departure. Gas valve confirmed on. See attached checklist for full tune-up details.

Performed heating maintenance on one heat pump system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. I found that one of her UV lights has failed. I presented options for repair to the customer, and she chose to have it replaced at this time. I replaced the UV light and cycled power at the thermostat. No other major issues were found, and the system is operational at this time. See attached checklist for full tune-up details.

Performed heating maintenance on one furnace system. Checked all electrical, mechanical and performance of the system. I replaced filters that were provided by the customer. I also advised the owner and the tenant that they replace the filters sooner to prevent any stress on the blower motor. The tenant informed me that she felt her son and daughter’s room were not getting any air out of the supply vents. I used my meter and found that the rooms have a temperature rise of 40°- 45°. No other major issues were found, and the system is operational at this time. See attached checklist for full tune-up details.

Performed heater check on a Carrier heat pump. Checked electrical, mechanical, safety, and performance of the system. Air handler, evaporator coil and blower are all clean. Heat kit is operational and all strips working during test. Drain line was cleared and treated. Condenser capacitor is within value. Contactor and electrical connections are in good condition. Condenser fan motor is showing signs of overheating. Condenser coil was cleaned. Options for repair were presented to the homeowner but they declined repairs today. System was running at the time of departure. See attached checklist for full tune-up details.

Performed heater maintenance on one gas furnace system. Checked electrical, mechanical, safety, and performance of the system. Flame ignition achieved, gas pressures adjusted, and flame sensor cleaned. Filter was clean as it was recently changed by the homeowner. I did notice some buildup on the indoor blower wheel. Brought this to the homeowner’s attention and he decided to hold off on cleaning at this time. No other major issues found and system was running at time of departure. Gas valve confirmed on. See attached checklist for full tune-up details.

Performed heating maintenance on one furnace system. Checked all electrical, mechanical and performance of the system. I talked to the customer about adding a water safety switch on the secondary drain line and he chose to have it installed at this time. After installing the water safety switch, I confirmed that the furnace is operational. No other major issues were found. See attached checklist for full tune-up details.

Performed diagnostic. I found that the drain line for the 90% furnace had frozen and was backing up water into the water safety switch. I thawed out the drain line and cut it shorter to prevent the water from freezing. I also insulated the drain line and confirmed the water was draining properly. No other major issues were found. System is on and working at this time.

Performed heater check on a Carrier gas furnace. Checked electrical, mechanical, safety, and performance of the system. Return and supply plenums are clean. Blower wheel is also clean. Flame sensor was cleaned. Igniter and inducer fan motor are at factory specifications. No major issues were found. Drain line cleared and treated. System was running at the time of departure. See attached checklist for full tune-up details.

Performed heater maintenance on one electric heat system. Checked electrical, mechanical, safety, and performance of the system. Both heat strips activated. Filter recently changed by homeowner and in good condition. Blower wheel and coil are clean. The drain line is clear. Capacitor is within value and condenser is also clean. No major issues were found and system running at time of departure. See attached checklist for full tune-up details.

Performed heater maintenance on one heat pump system. Checked electrical, mechanical, safety, and performance of the system. Heat strips activated. Filter is dirty but the customer did not have a replacement. Indoor blower and coil are clean. UV light is operational. Drain line was cleared. Outside condenser refrigerant pressures within range and condenser is clean. Capacitor is within value. No major issues were found and system running at time of departure. See attached checklist for full tune-up details.