Kyle TX Heating & Air Conditioning Services

Performed heat maintenance on one gas furnace. Checked electrical, mechanical, safety, and performance of the system. Flame ignition achieved, gas pressures adjusted, and flame sensor cleaned. Filter changed with customer supplied filter. No major issues were found and system running at time of departure. Gas valve confirmed on. See attached checklist for full tune-up details.

Performed heat check on a Rheem heat pump. Checked electrical, mechanical, safety, and performance of the system. Electric heat strips are operational. Low voltage wiring had a loose connection at the wire nut for the R wire. I made sure the connection was solid and tightened down the wire nut. Drain line was cleared and treated. Blower motor capacitor is in spec. Air handler and blower wheel are clean. Refrigerant and condenser capacitor are within spec. Condenser coil was cleaned. Surge protection for the air handler and the condenser are operational. Electrical disconnect confirmed in and on. System was running at the time of departure. See attached checklist for full tune-up details.

Performed heat check on an electric heat system. Checked electrical, mechanical, safety, and performance of the system. The evaporator coil, air handler and blower wheel are all clean. All heat strips are operational and running at 20 amps. No major issues were found with the system. Drain line was cleared and treated. Condenser coil clean. Electrical disconnects confirmed in and on. System was running at the time of departure. See attached checklist for full tune-up details.

I began my diagnostic by opening up the air handler unit. I found that the low voltage control fuse was blown. I went to the outdoor heat pump and opened up the electrical panel and immediately smelled an electrical burn odor. I tested the control starter and found that it had failed with a direct short across the coil. Recommended replacing the starter to return system back to operation. The customer agreed. Installed new outdoor starter, tested system and verified operation. Everything is working at this time.

Performed heater maintenance for one gas furnace system. Checked electrical, mechanical, safety, and performance of the system. Flame ignition achieved and gas pressure adjusted. Flame sensor cleaned. Filter was clean and recently changed by homeowner before arrival. During the maintenance, the homeowners mentioned to me that they were interested in duct cleaning as well as a dryer vent cleaning. I presented options to them, but they decided to hold off for the time being. No other major issues were found and system running at time of departure. Gas valve confirmed on. See attached checklist for full tune-up details.

Performed heater maintenance on one heat pump system. Checked electrical, mechanical, safety, and performance of the system. Heat strips activated with no issues and filter was clean. Indoor coil and blower are both clean. Outside condenser refrigerant pressures are within range and condenser is clean. Capacitor within value. No major issues were found, and the system was running at time of departure. See attached checklist for full tune-up details.

Replaced a failed Synergy Air Purifier with a Solaris Air Purifier. Confirmed purifier is on and working. No other issues were found. System is on at this time.

Performed heating maintenance on one gas furnace system. Checked all electrical, mechanical and performance of the system. I found that the filter on the system is the incorrect size. I informed the homeowner and suggested that he buy Honeywell filters to prevent any filter bypass. I added foam tape insulation to the current filter until the customer is able to purchase and replace it with a new Honeywell filter. No other major issues were found, and the system is operational at this time. See attached checklist for full tune-up details.

Performed semiannual maintenance on one gas furnace heating system. Inspected all Performance, Mechanical and Safety Systems. Adjusted fuel pressure of the furnace to match the system output rating to ensure 100% heating capacity for the home. When I arrived, I found that the homeowners had changed out their AprilAire 410 filter prior to us arriving so the filter installed was in good condition and did not need to be changed. I ensured all electrical terminals and connections were secured and properly fitted. Also verified the furnace combustion process was running cleanly and safely. Verified everything was operating within manufacture’s specifications for operation. Everything is working at this time. See attached checklist for full tune-up details.

During my evaluation of the system I noticed the following: there is mold buildup inside the supply plenum, the blower motor has failed and won’t turn off, the contactor is pitted and charred, and the condenser fan motor is leaking oil. I brought all of this to the attention of the homeowner and wrote up a list. He elected to have the contactor, blower motor, and condenser fan motor replaced, as well as have our Breathe Easy Stage 4 installed. I took care of the contactor and condenser fan motor outside. I installed the Solaris system and then installed the blower motor. I got the system turned on and tested it in all modes. System is in working order at completion of appointment.

During my evaluation of the system I noticed the following: there is mold buildup inside the supply plenum, the blower motor has failed and won’t turn off, the contactor is pitted and charred, and the condenser fan motor is leaking oil. I brought all of this to the attention of the homeowner and wrote up a list. He elected to have the contactor, blower motor, and condenser fan motor replaced, as well as have our Breathe Easy Stage 4 installed. I took care of the contactor and condenser fan motor outside. I installed the Solaris system and then installed the blower motor. I got the system turned on and tested it in all modes. System is in working order at completion of appointment.

During my evaluation of the system I noticed the following: there is mold buildup inside the supply plenum, the blower motor has failed and won’t turn off, the contactor is pitted and charred, and the condenser fan motor is leaking oil. I brought all of this to the attention of the homeowner and wrote up a list. He elected to have the contactor, blower motor, and condenser fan motor replaced, as well as have our Breathe Easy Stage 4 installed. I took care of the contactor and condenser fan motor outside. I installed the Solaris system and then installed the blower motor. I got the system turned on and tested it in all modes. System is in working order at completion of appointment.

During my evaluation of the system I noticed the following: there is mold buildup inside the supply plenum, the blower motor has failed and won’t turn off, the contactor is pitted and charred, and the condenser fan motor is leaking oil. I brought all of this to the attention of the homeowner and wrote up a list. He elected to have the contactor, blower motor, and condenser fan motor replaced, as well as have our Breathe Easy Stage 4 installed. I took care of the contactor and condenser fan motor outside. I installed the Solaris system and then installed the blower motor. I got the system turned on and tested it in all modes. System is in working order at completion of appointment.

Performed a heat check on a Carrier gas furnace. Checked electrical, mechanical, safety, and performance of the system. Return and supply ducts are clean. Air handler and blower wheel are also clean. Igniter is in value and operational. Flame sensor was cleaned. Inducer motor was running at normal amperage. Condensate drain was partially clogged. I cleared the drain and flow tested it with water. I also treated the drain line. The furnace ran through the sequence of operation and heated for 20 minutes without issue. Temperature rise was about 35 degrees. No major issues with the system were found. Thermostat was set to auto at the customer’s chosen setting. System was running at the time of departure. See attached checklist for full tune-up details.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. Both heat strips activated. Filter was replaced by customer supplied filter. Blower wheel and coil are clean. Outside condenser refrigerant pressures are within range and condenser is clean. The capacitor is within value. No major issues were found and the system was running at time of departure. See attached checklist for full tune-up details.