Kyle TX Heating & Air Conditioning Services

I checked over the unit and found everything to be in really great shape. All heating components checked out fine and are operating within spec. I did adjust the low pressure on the gas valve from 2.2” WC down to about 1.6” WC per the manufacturer’s instructions. I observed a temperature rise within range on the manufacturers label. System is in working order at completion of appointment. See attached checklist for full tune-up details.

Performed semiannual maintenance on one gas furnace. Inspected all Performance, Mechanical and Safety systems. Verified everything was operating within manufacture’s specifications for operation. I verified that all Stage 3 and Stage 4 Breathe Easy Systems were on and operating as designed while on-site. Also verified that the furnace surge protection is still operating and green lit showing active protection. The current furnace filter was still clean from the previous visit. Everything is working at this time. See attached checklist for full tune-up details.

Performed semiannual maintenance on one gas furnace heating system. Inspected all Performance, Mechanical, and Safety systems. I adjusted the fuel pressure to match the system output rating to ensure 100% heating capacity of the furnace system. The homeowner changed both air filters prior to our arrival. Verified everything was operating within manufacture specifications for operation. Everything is working at this time. See attached checklist for full tune-up details.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. Both heat strips activated. Filter was dirty, but homeowner did not have a replacement. I did have replacement filters on my van, so I replaced it today. Upon inspection of the outside condenser, I noticed that the fan motor is showing signs of overheating. Brought this to the homeowner’s attention, but she declined today and would like to look into doing the work at the Spring checkup. No other major issues were found, and the system is running at time of departure. See attached checklist for full tune-up details.

Performed heat check on two systems. Checked electrical, mechanical, safety, and performance of both systems. All heat strips on both systems activated. Both filters on each system are dirty and I let the homeowner know they would need to get some replacements ASAP. I also noticed that the insulation on both indoor panels was coming loose, so I secured that with some aluminum tape. Outside condensers refrigerant pressures are within range and both condensers were clean. No other major issues were found and the system was running at time of departure. See attached checklists for full tune-up details.

Install new American Standard 4-ton condenser. Moved the filter dryer into the attic. Pressure tested with dry nitrogen and pulled a vacuum on copper line set. Removed the duct running off of the satellite plenum and patched the hole. Ran a new 12” flex run to a 12x9x9 wye. Took one of the wyes to the back bedroom and increased the bucket to a 14x8x9. Took the other 9 to a 9x7x7 wye running to the sunroom where two 12x6x7 buckets were cut in. An additional 10x10x8 return bucket was cut into the sunroom as well. A new 8x4x5 bucket was cut into the pantry closet.

HVAC Repair: Arrived at the client’s residence to perform repairs on their inoperable furnace. Upon investigation, a faulty relay was identified as the cause of erratic AC operation. To rectify the issue, we promptly and precisely replaced the malfunctioning relay. This meticulous intervention guaranteed consistent and reliable cooling, restoring the overall efficiency of the air conditioning system and ensuring a comfortable indoor environment.

Heat Pump Repair: Addressing a customer's concern about a heat pump not defrosting properly, we determined a malfunctioning defrost sensor. After replacing the sensor and fine-tuning the heat pump, efficient operation was restored. Periodic maintenance suggestions were provided to prevent similar issues in the future, ensuring the client's home remains comfortably heated.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. Drain line was cleared and treated. Filter was dirty and the customer did not have a replacement at this time. Furnace and blower wheel are clean. Amp draw on the inducer motor is normal, and the igniter is in value. I cleaned off the flame sensor and I also sealed the door to the air handler with tape. Customer stated that she had caught a rodent in the attic. I looked at the ductwork in the attic and didn’t find any damage or leaks. No major issues were found and system was running at the time of departure. See attached checklist for full tune-up details.

I went through the thermostats and set them both to heat so I could test all the mechanical modes. I verified they turned on and off as designed. I went to the thermostat on the Northwest side of the home and set the setpoint below the actual interior house temp and set it to “Emergency Heat”. The system and heater automatically came on even with the thermostat below setpoint and continued to run constantly. The homeowner did mention that she found that specific thermostat set to “Emergency Heat” when she first came back to the house. I recommended replacement of the thermostat to ensure all cooling and heating functions operate as they’re designed too and to help ensure a constant level of comfort inside the home. Replaced thermostat and test function. System operating properly at this time.

Performed heater maintenance. Checked electrical, mechanical, safety, and performance of the system. Both heat strips activated. Filter was recently changed by the homeowner. Tightened down wiring on the inside system. Outside condenser refrigerant pressures are within range and condenser was clean. No major issues were found and system running at time of departure. Please see attached checklist for full tune-up details.

Precise Air Conditioner Maintenance: Faced with uneven cooling at a client's residence due to blocked air vents and ductwork obstructions, we promptly implemented a solution. Cleaning vents and adjusting ductwork restored balanced airflow, ensuring consistent cooling throughout the home.

Ductless Heat Pump Maintenance: Confronted with issues in a client's ductless heat pump related to the damper motor, our strategic repair involved replacing the malfunctioning motor. This ensured efficient temperature control in various zones, optimizing comfort for the client through our skilled technicians' intervention.

Heat Pump Installation: Collaborating closely with a residential client, we facilitated the installation of a new, high-efficiency Carrier heat pump to meet their heating and cooling needs. Our process began with a detailed assessment of the home's specific requirements and the client's preferences. Once the optimal Carrier heat pump model was selected, our skilled technicians expertly installed the unit, ensuring precision in connecting components and aligning ductwork. Rigorous testing followed to verify the system's seamless operation, providing the homeowner with enhanced energy efficiency, reliable heating, and cooling performance for year-round comfort.

AC System Replacement: Collaborating closely with a residential client, we orchestrated the seamless replacement of their outdated air conditioning system. Our process commenced with a meticulous evaluation of the client's cooling requirements and preferences. After selecting an advanced and energy-efficient AC system, our skilled technicians expertly removed the old unit, ensuring precision in connecting the new components and aligning the ductwork. Rigorous testing followed to confirm the new system's optimal performance, delivering enhanced cooling efficiency and comfort for the homeowner.