Kyle TX Heating & Air Conditioning Services

Performed heater maintenance. During my maintenance I checked over all the electrical wiring and noticed that some was slightly loose; I tightened down the connections. I then checked over the flame sensor and igniter; both are clean. Gas pressures are correct with no leaks. Filter was dirty so I changed it out with a customer supplied filter. Checked over supply and return ducts for leaks. No other major issues were found, and system was running at time of departure. Gas valve confirmed on.

Performed heat check on Carrier heat pump system. Checked electrical, mechanical, safety, and performance of the system. Air handler and blower wheel are clean. Electrical heat strips are operational. Surge protection for the system is also operational. I cleared the drain line and flow tested the line with water. I then treated the drain line. Condenser coil was cleaned. Electrical disconnect confirmed in and on. System was set to customer’s desired temperature. No major issues were found, and system is operational. See attached checklist for full tune-up details.

Performed heat check on down flow electric heater. Checked electrical, mechanical, safety, and performance of the system. All electric heat strips were on. Drain line was cleared and treated. Air handler, blower wheel and evaporator coil are clean. Condenser coil is clean and free of debris. I sprayed the electrical cabinet of the condenser with JS insecticide. No major issues were found and system was running at the time of departure.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. All heat strips activated. Filter was clean, but damaged, and homeowner did not have a replacement. Noticed insulation on the inside of panel door was coming loose, so I secured it back to the door. No other major issues were found and the system was running at time of departure.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. Flame ignition achieved, gas pressure adjusted, and flame sensor cleaned. Filter changed by homeowner prior to arrival. No major issues were found and system running at time of departure. Gas valve confirmed on.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. One of the nuts holding the inducer motor had come loose and the motor was vibrating when running. I tightened down the nut and the vibration stopped. No other major issues were found. See attached checklist for full tune-up details. Drain line was cleared and flow tested with water. Drain line was treated. Air filter was replaced and dated with a customer supplied filter. System was running at the time of departure.

Performed heating maintenance on one heat pump system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. Replaced two filters. I found that all three UV lights were not working at the air handler. I installed another transformer and separated one of the UV lights from the circuit. I cycled power and all three UV lights are now working. Air purifier and both surge protectors are working as well. No other major issues were found and system operational at this time.

Performed heating maintenance on one heat pump system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. I found that the disconnect box is broken and has been bypassed. I informed the homeowner and presented options for replacing it; she declined repairs at this time. No other major issues were found and system is operational at this time.

Performed inspection. I found that the door panel screw holder has failed and is causing the furnace panel to fall off. I presented options to the homeowner, and she chose to have it replaced. I taped the door to prevent it from falling until we are able to make the repairs. Parts have been ordered and we will return to complete repairs once received. Returned and performed a whole house duct cleaning. Replaced the furnace door screw. Cleaned out the dryer vent as well. Checked to make sure the system was operating properly.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. Flame ignition achieved, gas pressure adjusted, and flame sensor cleaned. Filter changed with customer supplied filter. During my maintenance I found that some of the wiring was loose and the door switch not activating properly. I tightened the wiring and adjusted the door switch. No other major issues were found and the system was running at time of departure. Gas valve confirmed on.

Performed semiannual maintenance on one comfort heating heat pump system. Inspected all Performance, Mechanical and Safety Systems. I checked over the system and discovered the following: the hard start device has failed, and the contactor has major pitting and charring. No other major issues found. See attached checklist for full tune-up details. I brought my findings to the attention of the homeowners. They elected to renew their maintenance agreement, have the contactor replaced, and also remove the hard start device to replace it with a soft start device designed to lengthen the lifespan of their unit. I got straight to work on installing the soft start for the heat pump. Mounted the soft start and then wired up the rest of the system.

Performed semiannual maintenance on one comfort heating heat pump system. Inspected all Performance, Mechanical and Safety Systems. I checked over the system and discovered the following: the hard start device has failed, and the contactor has major pitting and charring. No other major issues found. See attached checklist for full tune-up details. I brought my findings to the attention of the homeowners. They elected to renew their maintenance agreement, have the contactor replaced, and also remove the hard start device to replace it with a soft start device designed to lengthen the lifespan of their unit. I got straight to work on installing the soft start for the heat pump. Mounted the soft start and then wired up the rest of the system.

Performed semiannual maintenance on one comfort heating heat pump system. Inspected all Performance, Mechanical and Safety Systems. I checked over the system and discovered the following: the hard start device has failed, and the contactor has major pitting and charring. No other major issues found. See attached checklist for full tune-up details. I brought my findings to the attention of the homeowners. They elected to renew their maintenance agreement, have the contactor replaced, and also remove the hard start device to replace it with a soft start device designed to lengthen the lifespan of their unit. I got straight to work on installing the soft start for the heat pump. Mounted the soft start and then wired up the rest of the system.

Performed semiannual maintenance on one comfort heating heat pump system. Inspected all Performance, Mechanical and Safety Systems. I checked over the system and discovered the following: the hard start device has failed, and the contactor has major pitting and charring. No other major issues found. See attached checklist for full tune-up details. I brought my findings to the attention of the homeowners. They elected to renew their maintenance agreement, have the contactor replaced, and also remove the hard start device to replace it with a soft start device designed to lengthen the lifespan of their unit. I got straight to work on installing the soft start for the heat pump. Mounted the soft start and then wired up the rest of the system.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. Flame ignition achieved and flame sensor cleaned. Filter changed with customer supplied filter. No major issues were found and system is operational at time of departure. Gas valve confirmed on. See attached checklist for full tune-up details.