Kyle TX Heating & Air Conditioning Services

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. No major issues were found. Drain line was cleared and flow tested with water. Drain line was treated. Condenser coil clean. Electrical disconnect confirmed in and on. System was running at the time of departure.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. No major issues were found. Drain line was cleared and treated. Condenser coil clean. Electrical disconnect confirmed in and on. System was running at the time of departure.

Performed heat check on two systems. Checked electrical, mechanical, safety, and performance of the systems. The Carrier system has some mold/mildew growing on the top of the evaporator coil. No other major issues were found. Drain lines were cleared and treated. Condenser coils clean. Electrical disconnects confirmed in and on. Systems were set to the customer’s desired temperature and were running at the time of departure.

Performed heating maintenance on a gas system. Checked all electrical, mechanical and performance of the system. Cleared and treated drain line. No major issues were found. System is on and working at this time.

Performed heating maintenance. Checked all electrical, mechanical and performance of the system. I found that the furnace was not kicking into 2nd stage heating. I moved dip switch S2 #10 into the on position. I reset power and the system is now kicking into 2nd stage heating after 10 minutes. No other major issues were found. System is working properly at this time.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. No major issues were found. Drain line was cleared, flow tested with water then treated. Condenser coil clean. Zone control board is operational. System was running at the time of departure

On arrival, the homeowner stated that he turned the heater on, but there was no air blowing out of the supply vents. I opened up the furnace and found the low voltage fuse blown. I installed a new fuse and turned the heater on; this caused the heater to immediately blow the fuse. After diagnosing the system, found that the blower safety switch was rubbing out against the motor shaft of the blower motor causing it to spark. Repaired the rub out and secured the wire inside the furnace. Tested operations and everything is now working properly at this time.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. Flame ignition achieved and flame sensor cleaned. Filters are dirty but no replacements available. Homeowner mentioned that the drain line may be clogged and after further inspection, I did determine that the drain line was slightly clogged. I cleared it and applied some drain treatment. No other major issues were found and system running at time of departure.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. Flame ignition achieved and flame sensor cleaned. Filter changed with customer supplied filter. I also cleaned a few of the customer’s vents with the vacuum. No major issues were found and system running at time of departure.

On arrival, the customer informed me that the condenser was not working. I found that the breaker at the main panel was tripped. I reset the breaker and found that the capacitor had failed. After replacing the capacitor, I reset the breaker and found that it was not passing any voltage to the condenser and has failed as well. I spoke to the customer, and he told me he’s having problems with the breakers tripping for different areas of the house. He chose to just have the capacitor replaced for today and will call an electrician to come out and possibly replace the main breaker panel.

Performed diagnostic. I found that the outdoor capacitor (45/5) has failed. I informed the homeowner and presented options to repair. She chose to have it replaced at this time. I replaced the capacitor and secured it. Cycled power and no other major issues were found. System is on and running at this time.

Performed diagnostic. I found that the primary drain line had clogged, and the water safety switch had tripped. I cleared and tested the drain with 2 gallons of water. Once water was confirmed to be draining, I added drain treatment. I ran the system for 15-20 minutes no other major issues were found. System is on and working at this time.

Performed heating maintenance on a furnace system. Checked all electrical, mechanical and performance of the system. Cleared and treated drain line and washed the outdoor condenser coil. I found that the condenser fan motor is leaking lubricant. I informed homeowners and they asked that I send an estimate for the motor. No other issues were found. System is on and running at this time.

Performed diagnostic. I found that the main breaker for the condenser has failed and was only sending 80v. I informed the customer and he said he had an extra breaker (30a) to replace it with. I replaced the breaker, and the condenser is now getting 240V. System is operational and no other major issues were found.

Performed diagnostic. I found that the primary drain line was clogged, and it had tripped the water safety switch on the secondary line. The filter is also bent and air is not being filtered correctly. I replaced the filter and taped it to prevent this from happening. I presented my findings to the homeowner, and he chose to sign up on our Gold Maintenance Plan. I checked all electrical, mechanical and performance of the system. Cleared and flow tested the drain line with 2 gallons of water. I also treated the drain line and washed the outdoor coil. No other major issues were found. System is on and running at this time.