Kyle TX Heating & Air Conditioning Services

Performed heating maintenance on a gas system. I checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and the customer supplied two filters for replacement. Customer did inform me he had seen an oil like substance by the suction line at the condenser. I inspected the system and performed a leak check at the condenser. No issues were found. System is on and working at this time.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. Flame ignition achieved and flame sensor cleaned. Filter changed with customer supplied filter. No major issues were found and system running at time of departure.

Performed heating maintenance on a gas system. Checked all electrical, mechanical and performance of the system. I also cleared and treated the drain line. I informed the customer that her filter is dirty and needs replacement ASAP. No other major issues were found. System is running at this time.

Performed heating maintenance on a gas system. Checked all electrical, mechanical and performance of the system. I cleared and treated the drain line and washed the outdoor coil. I found multiple deficiencies with the system and presented my findings to the homeowner; he declined repairs at this time.

On arrival, I spoke with the current tenant residing inside the home and she stated that over the weekend they would set both the upstairs and downstairs zone thermostats to cool mode, however interior home temp would not get below 82°. I turned on both thermostats to cool mode and inspected the outdoor condensing unit. I found the compressor running but the fan motor shut off. I inspected all electrical items inside the unit and found that the fan motor has failed completely. Recommended replacing fan motor to return system back to operational. Installed new outdoor condenser fan motor, programmed motor to match OEM speed setting and tested the cooling system. Everything is working at this time. **While on-site, went ahead and secured the downstairs zone thermostat to the wall, at no additional charge, as it was very loose due to the wall anchor being not properly set.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. Flame ignition achieved and flame sensor cleaned. Filters were dirty, but customer did not have replacements. No major issues were found and system running at time of departure.

Service diagnostic found that the capacitor on the condenser unit has failed. Secondary drain line was set up to drain directly into the secondary pan. Options for repair were presented to the customer and they chose to have the capacitor replaced. Capacitor was replaced and the system was function checked. System was running at the time of departure.

Removed the old system from the closet and installed the new system in the attic space. Installed new 2.5-ton Carrier system. Installed new Ecobee Lite thermostat. Rebuilt and insulated condensate drain line. Added SS2 and SS3 safety float switches. Installed new filter dryer, pressure tested with dry nitrogen and pulled a vacuum on the copper line set. Added new supply and return plenums and sealed with mastic airlock. Charged system to factory spec. System is working properly at time of departure.

Installed new Carrier gas system. Added a new secondary drain pan and raised up system on foam blocks. Rebuilt drain line with SS-2 and SS-3 safety switches. Cleared drain line with CO2 and ran new control wire to the thermostat. Built supply and return plenums and reputed gas line. Installed new line filter dryer and pressure tested system for extensive leak check. Pulled deep vacuum and released refrigerant. Removed all the old ductwork and i-boxes. Went back with new flex duct and new i boxes. Replaced all the grills in the house. Replaced the return and supply plenums.

Performed semiannual maintenance on one heat pump heating system. Inspected all Performance, Mechanical and Safety Systems. Verified everything was operating within manufacture’s specifications for operation. While on-site, flushed and treated the primary drain line. Homeowner mentioned they were noticing high humidity inside the home as well. Found that the thermostat fan mode was set to constant on, which was causing the condensation on the coil to evaporate, increasing humidity inside the home. Set the fan mode back to auto to ensure that the fan motor turns on and off with the heating and cooling system. Did verify the Stage 4 Whole Home Air Purifier and Surge Protection Devices are on and operating as design. Everything is working at this time

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. Rust was found on the heat exchangers. Drain line was cleared, flow tested with water and treated. System was running at the time of departure.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. Flame ignition achieved and flame sensor cleaned. Filter changed with customer supplied filter. No major issues were found and system running a time and departure.

Performed heater tune-ups on two systems. Checked electrical, mechanical, safety, and performance of the system. Flame ignitions achieved and one flame sensor was cleaned, but the other one was corroded and needed to be replaced. Filter changed by homeowner before arrival. No other major issues found. Replaced corroded flame sensor and tested system. Both systems are operational upon departure.

Performed both a heat check and cool check on the AC system. Checked electrical, mechanical, safety, and performance of the system. Flame ignition achieved and flame sensor cleaned. Filters had already been changed by homeowner before arrival. Verified everything was operating within the manufacture specifications. I did find some deficiencies with their system. I compiled a list and brought those to the homeowner’s attention. He decided to move forward with just the mandatory repairs today. Replaced fan motor and capacitor. Tested system and it is operational at this time.

Diagnostic found that the system was leaking water around the drain line where the drain line connects to the primary pan. I confirmed that the drain itself was flowing water. I checked the system, and it was cooling normally with no airflow issues. I opened the evaporator coil and found that sludge had clogged the primary pan and was preventing water from flowing into the drain line. I cleared the pan and removed the sludge. I then cleared the drain line from the primary pan. I flow tested the drain by pouring water directly into the primary pan. I then closed the panel and resealed the evaporator coil housing. System was function checked and was running at the time of departure.