Kyle TX Heating & Air Conditioning Services

Replaced the Indoor evaporator coil. Rebuilt the drain and insulated it. Replace the inline filter dryer, pressure tested with dry nitrogen and pulled a vacuum on the copper line set. Charged the system to factory specs and washed off the condenser. The system is working properly at this time.

Performed service diagnostic. Diagnostic found that the capacitor on the condenser unit has failed. Start assist was allowing the compressor to run but the condenser fan motor was not operational. Options for repair were presented to the customer and they chose to have the capacitor replaced today. The condenser capacitor was replaced, and the system was function checked. Condenser fan motor is operational, and the compressor was running. System operation was confirmed with an electrical and pressure check of the system. System was running at the time of departure.

On arrival, I found the outdoor fan motor was not spinning. I tested the outdoor run capacitor and found it to be low on charge. Also noted the outdoor condenser fan motor has overheated in the past. Presented repair options and the homeowner decided to move forward with replacement of both components. Installed a new outdoor condenser fan motor and run capacitor. Reset the cooling system and everything is now working at this time.

Replaced secondary drain pan underneath cased coil. Installed new foam blocks and added SS-3 water sensing switch. Cleared drain line and treated. Verified system operation. Everything is working at this time.

Installed Carrier 3-ton gas system. Installed new Ecobee Pro thermostat. Installed new supply and return plenums and sealed with mastic air lock. Replaced secondary drain pan. Rebuilt and insulated primary and secondary drain. Installed SS2 and SS3 safety float switches. Cleared and verified drain operation. Replaced liquid line filter dryer, pressure tested the line set with nitrogen and pulled a vacuum on the line set. Replaced disconnect and whip at the outdoor condensing unit. Verified system charge and verified system operation.

Installed new 4-ton Carrier gas system. Installed two new Ecobee thermostats. Installed new bull head supply plenum and a new return air plenum, and then sealed with mastic air lock. Reused and installed the old zoning equipment. Replaced secondary drain pan. Added SS2 and SS3 safety float switches. Rebuilt and insulated condensate drain. Replaced disconnect and whip at the outdoor system. Pressure tested with dry nitrogen and pulled a vacuum on the copper line set. Charged system to factory specifications. System is working properly at time of departure.

On arrival, I turned the cooling system to the on position. Went outside to inspect the outdoor unit and found that the compressor was not turning on. Removed the condensing unit’s electrical panel and found the run capacitor to have failed across all terminals. Recommended having a new run capacitor installed today to return system back to factory specifications. Spoke with homeowner and we have decided to move forward with the repair. Installed new capacitor, tightened and secured all electrical terminals and installed two new high voltage wire nuts on the line side electrical whip. Reset the cooling system and verified system startup. Everything is working at this time.

Performed service diagnostic. Diagnostic found that the condensate drain line was clogged. Options for repair were presented to the customer and they chose to move forward with drain service today. Drain line was cleared and flow tested with water. Drain line was treated. System was running at the time of departure.

Performed service diagnostic. Diagnostic found that the condensate drain line was clogged. Water had backed up into the safety switch. Options for repair were presented to customer and they chose to have the drain serviced today. Drain line was cleared and flow tested with water. Drain line was treated. System was running at the time of departure.

Performed service diagnostic. Diagnostic found that the condensate drain line was clogged. Water had backed up into the safety switch. Options for repair were presented to customer and they chose to have the drain serviced today. Drain line was cleared and flow tested with water. Drain line was treated. System was running at the time of departure.

Performed service diagnostic. Diagnostic found that the condensate drain line was clogged. Options for repair were presented to the customer and they chose to have the drain line cleared and to sign up for maintenance. First maintenance visit will be in Fall/Winter of this year. Drain line was cleared and flow tested with water. Drain line was treated. System was function checked and was running at the time of departure.

Installed complete new duct system in attic. Added new fabricated extended supply plenum with balancing dampers. Installed new I-boxes and sealed all pressure points with air lock. Hung and strapped ductwork and added French drain outside. System operating at this time.

Performed service diagnostic. Diagnostic found that the condensate drain line was clogged. Options for repair were presented to the customer and they chose to have the drain line cleared and sign up for our annual maintenance plan. Drain line was cleared and flow tested with water. Drain line was treated. System was function checked and was running at the time of departure.

Performed the AC tune-up. Cleared and treated drain line. Condenser coil clean. I found that the condenser fan motor is showing signs of lubricant leakage. No other major issues found.

Performed diagnostic. I found that the outdoor condenser motor was burnt and had failed. I informed the homeowner, and he chose to have it replaced today. I replaced the motor, and everything is working at this time.