Kyle TX Heating & Air Conditioning Services

Service diagnostic found that the low voltage fuse had blown. Options for repair were presented to the homeowner and he chose to have the wiring repaired. I replaced the damaged fuse and made solid connections on the wiring in the air handler. I function tested the system and the system was running at the completion of service.

Service diagnostic found the drain line was clogged and was causing the outdoor system to shutdown. I also found the furnace flue pipe is showing wear and tear. The system is low on refrigerant and the outdoor starter is pitted at the contacts. Spoke with the homeowner on the phone and he chose to have the drain line serviced today. I cleared and flushed the drain line and verified it is draining outside. I did ask them to keep an eye on the system as there could be other issues in the near future due to the age of the system. The system is operational at completion of service.

Performed a/c tune-up on a Carrier straight cool system. Checked the electrical, mechanical and performance systems of the unit. Replaced the return air filter. Cleared, cleaned, flushed and treated the drain line and washed the outdoor coil. The homeowner informed me their outdoor system was vibrating a lot recently. Checked over the system and was not able to hear any abnormal noises. I did add foam insulation to a weld on the fan shroud to prevent it from possibly causing a noise in the future. No major issues were found. All surge protection devices are working. The system is operational at this time.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

Service diagnostic found the primary drain clogged at the coil threaded connection. This was tripping the water safety switch and shutting off the outdoor system. Also found the system is slightly undercharged with refrigerant. The outdoor starter is pitted at the contacts. The indoor coil is also rusted out and prone to a refrigerant leak. Spoke with the homeowner and he chose to have the drain line cleared today. I cleared and treated the drain line and verified it is draining outside. The system is operational at completion of service.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was clean and was replaced by the homeowner earlier this week. No major issues were found. The system was running at the completion of service.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with water. I also treated the drain line. The air filter was new and had been replaced by the homeowner before my arrival. No major issues were found. The system was running at the completion of service.

Replaced 16x16 square damper. Sealed new damper. Sealed a part of the supply plenum. Tested zone board and damper operation. Cleared drain. Installed new condenser fan motor and programmed it. Installed EasyStart kit and cycled operation 5 times. Everything is working at completion of service.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with water. I also treated the drain line. The air filter was clean and had been recently replaced by the homeowner. I did find that the system does not have a safety float switch install on either the condensation drain line or the secondary pan. The system was running at the completion of service.

During my diagnostic, I found that the coil on the contactor out at the condenser was completely shorted. Because it was shorted the voltage moving through the contactor was too high and the low voltage fuse protecting the circuit had popped. I spoke to the homeowner and she chose to have the contactor replaced. I replaced the contactor. I also secured the high voltage wires from the compressor so they wouldn’t run out on the copper lines inside the condenser. The system is working at completion of service.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

Two system cool check was completed. Both drains were flushed and treated. Both outdoor coils were cleaned. All mechanical and electrical components were checked, along with refrigerant levels. On the upstairs condenser, I found the contactor charred and pitted. On the downstairs condenser, I found high in rush amps to the compressor. I recommend installing a soft start to lower the amps. The systems were running at completion of service.