Kyle TX Heating & Air Conditioning Services

Installed 3 ton Carrier R-454B heat pump system. Vertical air handler with heat kit in closet. Installed Ecobee pro thermostat. Installed new plywood overlay for the air handler to sit on. Built and installed new supply plenum. Sealed ductwork connections with mastic/hardcast. Installed new disconnect box and pad for the condenser. Pressure tested system with nitrogen and pulled vacuum. Rebuilt primary condensation drain, added secondary safety switch. Cleared with CO2 and primed with water. Charged AC with R-454B refrigerant. Tested heating and cooling operation of new system. Everything is working at completion of install.

Replaced supply plenum and all compromised portions of flex duct. Resealed plenum and ducting with air lock. Cleared drain line with CO2 and water. Verified system operation. Everything is working at this time

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with water. I also treated the drain line. The air filter had been recently replaced by the homeowner. No major issues were found. The system was running at the completion of service.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

AC cool check completed on a vertical heat pump system. Outdoor coils were cleaned. The drain line was flushed and treated. All mechanical and electrical components were checked. I did find high in rush amps to the compressor exceeding manufacturers limitations. I went over my findings and solutions with the homeowner. No other issues were found. The system was running at completion of service.

Installed Carrier 4 ton 2 stage heat pump. Installed 2 Ecobee pros. Installed new supply plenum and zoning plenums. Re routed bypass to feed into return. Installed new return air filter grilles. Installed new zone dampers and zone board. Installed plywood overlay. Sealed all connections. Rebuilt and insulated primary drain line. Installed SS2 Safety switch. Pressure tested lineset and pulled a vacuum. Installed new disconnect by the condensing unit. Tested system operation and weighed in additional charge as needed per manufacturer specifications. Everything is working at completion of install.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The homeowner wanted to change his thermostat to a thermostat with an Auto setting. I replaced his Honeywell T1 thermostat with a T6 thermostat. I function tested the system and went over operation of the new thermostat with the homeowner. The system was running at the completion of service.

Performed AC cool check on two systems. Checked the electrical, mechanical, safety, and performance of the systems. I cleared the condensation drain lines and flow tested the drains with two gallons of water. I also treated the drain lines. The air filters were clean and had been recently replaced by the homeowner. No major issues were found. The systems were running at the completion of service.

AC cooling check completed for a vertical straight cool system. The drain line was flushed and treated. The outdoor coils were cleaned. The mild increase in humidity levels inside the home is due to the moderate temperatures and extreme outdoor humidity levels. No major issues were found. The system is cooling properly at time of departure.

Performed A/C maintenance on a Carrier straight cool system. Checked the electrical, mechanical and performance systems of the unit. Cleared and treated the drain line and verified it is flowing outside. Resealed the air handler door with tape to keep the insulation in place. Washed the outdoor coil and verified the surge protection device is working. No major issues were found. The system is operational at this time.

Installed new heat pump system. Added plywood overlay in closet and rebuilt drain line. Installed new Ecobee thermostat and pressure tested system for extensive leak check. Pulled deep vacuum and verified system operation. System charged and everything is working at completion of install.

AC cool check completed on a vertical heat pump system. Drain line was flushed and treated. Outdoor coils were cleaned. All mechanical and electrical components were checked along with refrigerant level. I did find high in rush amps to the compressor and a charred and pitted contactor. No other major issues were found. The system is running at completion of service.

AC cool check completed for a horizontal straight cool system. Drain line was flushed and treated. Outdoor coils were cleaned. All mechanical and electrical components were checked along with refrigerant levels. I did find there is no surge protection on either unit. I also found in rush amps to the compressor slightly higher than manufacturers limit. No other major issues were found. The system is running at completion of service.

Performed A/C tune-up on a Lennox straight cool system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and sealed some air straws on the furnace. Secured outdoor compressor wiring and washed the outdoor coil. Replaced the return air filters for the homeowner as well. I did find the outdoor starter is pitted at the contacts. No other issues were found. The system is operational at this time.

Performed A/C tune-up on a Carrier Infinity system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. Secured outdoor compressor wiring and washed the outdoor coil. I did find the blower wheel has dirt/dust build up. No other issues were found. The system is operational at this time.