Kyle TX Heating & Air Conditioning Services

Installed 4 ton Carrier R-454B system. Gas furnace in closet. Installed Ecobee pro thermostat. New disconnect box for the condenser. New plywood overlay for the furnace to sit on, new gas pipe connections and new flue pipe connections. Build and installed new supply plenum. Sealed all ductwork connections with mastic/hardcast. Rebuilt primary condensation drain, added secondary safety switch. Cleared drain with CO2 and primed trap with water. Pressure tested system with nitrogen and pulled vacuum. Charged AC with R-454B refrigerant. Tested heating and cooling operation of system. Everything is working at completion of install.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

Performed A/C tune-up on a Carrier straight cool system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. Secured outdoor compressor wiring and washed the outdoor coil. I did adjust the airflow for the system. No major issues were found. The system is operational at this time.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was clean and had been replaced before my arrival. No major issues were found. The system was running at the completion of service.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

Performed service diagnostic. Diagnostic found that the condensation drain line was clogged. Options for repair were presented to the homeowner and he chose to have the drain line cleared. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. I then function tested the system and the system was operating normally. The system was running at the completion of service.

Performed a/c tune-up on a Carrier heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. Secured outdoor compressor wiring and washed the outdoor coil. I did find the outdoor starter is pitted at the contacts. The compressor is starting to do high amps on start up. The system also has high static pressure. No other issues were found. The system is operational at this time.

Performed A/C tune-up on a Carrier heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. Verified outdoor compressor wiring is secure and washed the outdoor coil. No major issues were found. The system is operational at completion of service.

Performed a/c tune-up on a Carrier straight cool system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. Secured outdoor compressor wiring and washed the outdoor coil. I did find the system overcharged with R410-A refrigerant. Spoke with the homeowner and he chose to recover refrigerant and bring the system back to manufacturer specs. Recovered 2lbs of refrigerant and the system is now operating at 10 degrees of subcooling. Ran the system for about 15 minutes to let the pressures stabilize. No other issues were found. The system is operational at this time.

Pumped down existing refrigerant to the condenser. Installed new evaporator coil in the attic. Installed new liquid line filter drier in the attic. Installed the Easy Start at the condenser. Pressure tested system with nitrogen and pulled vacuum. Made new condensation drain connections at the evaporator coil. Sealed ductwork connections to the new coil with mastic/hardcast. Cycled system on and off for the Easy Start to program. Tested system operation. Everything is working at completion of service.

Installed Carrier 4 ton furnace and condenser. Installed new supply plenum. Installed new plywood overlay. Leveled pad and installed new disconnect and whip. Ran low voltage in 1/2 inch seal tite. Rebuilt and insulated primary drain line. Installed SS2 safety switch. Cleared and tested drain. Pressure tested copper lineset and weighed in additional charge to meet manufacturers specifications. Tested system. Everything is working at completion of install.

AC cool check completed on a horizontal straight cool system. Drain line was flushed and treated. Outdoor coils were cleaned. All mechanical and electrical components were checked. I did find the unit without surge protection. I also found high in rush amps to the compressor. The system was cooling at completion of service.

AC cool check completed for a vertical straight cool system. Drain line was flushed and treated. Condenser coils were cleaned. All mechanical and electrical components were found within manufacturer specifications. However, the system did not have surge protection. I spoke to the homeowner about adding surge protection to her units and she chose to add it today. Outside surge protection was attached to the disconnect box securely and spliced into the high voltage wiring. Surge protection for the furnace was securely mounted to the side of the furnace and also spliced into high voltage wiring. After completing installation of surge protection, I function tested the system. The system is cooling properly at completion of service.

AC cool check completed for a horizontal heat pump. Outdoor coils were cleaned. Drain line was flushed and treated. All mechanical and electrical components along with refrigerant levels were checked. Everything was found operating within manufacturer specifications. The system is cooling at completion of service.

AC cool check completed on a vertical straight cool system. Drain line was flushed and treated. Outdoor coils were cleaned. All mechanical and electrical components were found within manufacturer specifications. No major issues were found. The system is cooling properly at time of departure.