Kyle TX Heating & Air Conditioning Services

Performed heating maintenance on a straight electric air handler heating unit. Inspected all performance, mechanical and safety systems. I flushed and treated the primary drain line. I did find that the indoor blower assembly had a significant amount of shaking and rattling while running. I went over my findings with the homeowner and due to the condition of the blower system, I provided him an estimate to replace the blower motor and blower wheel for the indoor air handler unit. Everything is working at this time.

Performed heater tune-up on a Carrier furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace system. I did find the blower wheel was dirty. I spoke with the homeowner and he chose to have the blower wheel cleaned. I pulled and cleaned the blower wheel and blower housing. Installed the blower housing back in place and function tested the system. No other issues were found. The system is operational at this time.

Performed heater tune-up on a Goodman 90% furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. I did find the blower wheel is starting to accumulate dust. The system also has high static pressure on the return side but due to the location there is no room for improvement. No other issues were found. The system is operational at this time.

Disconnected dryer and pulled away from connections. Used brush attached to rods with a drill to clean out the dryer vent up to the roof penetration. Cleaned the vents and connection piece on the back of the dryer. Inspected vent pipe with camera to verify that it was cleaned out. Cleaned out the dryer filter area. Reconnected dryer and powered on to verify it is working. Everything is working at completion of service.

Installed furnace and condenser. Re used thermostats and zoning equipment. Installed new plywood overlay. Built a transition to existing duct work. Sealed all connections with mastic. Rebuilt primary and secondary drain lines. Cleared drain and verified operation. Installed new condenser pad and leveled it. Reinsulated suction line. Ran low voltage in 1/2 inch seal tite. Pressure tested lineset and pulled a vacuum. Weighed in additional refrigerant. Everything is working at completion of service.

Heat check completed on a vertical furnace. Flame sensor was cleaned. Drain line was flushed and treated. All mechanical and electrical components were tested. The system is running at completion of service.

Heat check completed on a vertical furnace. Drain line was flushed and treated. Flame sensor was cleaned. All mechanical and electrical components found within manufacturer specifications. The system was running at completion of service.

Heating tune-up completed on a horizontal heat pump system. Drain line was flushed and treated. Outdoor coils were cleaned. I did find significant biological growth in the supply plenum. I also found the static pressure exceeding manufacturers recommended limit. On the outdoor unit, I found the condenser fan motor leaking lubricant as well as in rush amps to the compressor exceeding manufacturers limitations. I went over my findings with the homeowner.

Performed heater tune-up on a Carrier heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. I did find the outdoor capacitor is starting to lose power but is still within range. The outdoor fan motor has a hotspot and the outdoor compressor is doing high amps on start up. Spoke with the homeowner about my findings. No other issues were found. The system is operational at this time.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. I did find some biological growth inside the air handler on and around the evaporator coil. I went over what I had found with the homeowner and presented options for the biological growth inside the air handler. I wiped down the evaporator coil and the air handler to remove as much of the biological growth as I could. The system was running at the completion of service.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

Performed heater tune-up on a Carrier heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line. Cleaned the exterior of the furnace system and vacuumed the return air grille. I did find some insulation had been chewed off from the suction line. I repaired the insulation to help prevent any sweating. No other issues were found. The system is operational at this time.

Service diagnostic found that the blower motor inside the air handler has failed. The motor is getting power and signal to run however it will not start. Options for repair were presented to the customer and he chose to have the blower motor replaced today. I picked up a new motor and returned to complete the repair. I replaced the blower motor and function tested the system. The system was running at the completion of service.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain lines and flow tested the drain with two gallons of water. I also treated the drain line. The air filters are clean and had been replaced by the homeowner before my arrival. No major issues were found. The system was running at the completion of service.

Heat checked performed on a vertical furnace. Drain line was flushed and treated. Flame sensor was cleaned. I did find high static pressure on the system. No other issues were found. The system was running at completion of service.