Kyle TX Heating & Air Conditioning Services

Performed heater tune-up on a Carrier infinity furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace system. Replaced the high voltage wire nuts with a wago wire connector. I also found the water safety switch was not wired in correctly. I rewired the water safety switch and set up G Terminal Shutdown on the thermostat. Function checked the safety switch. No other issues were found. The system is operational at this time.

Heat check completed on a horizontal gas system. Drain line was cleared and treated. Flame sensor was cleaned. I did find the emergency drain pan full of rust and the blower motor leaking lubricant heavily. No other major issues were found. The system is heating at completion of service.

Performed heater tune-up on a Carrier two stage furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. No major issues were found. The system is operational at this time.

Performed heater tune-up on a Carrier furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line. Cleaned the exterior of the air handler and secured outdoor compressor wiring. The homeowner is doing some remodeling in the home and I asked her to keep an eye on the air filter since it is likely that it will get dirty due to all the dust in the air. I also took a look at the dryer vent and it is clean. No major issues were found. The system is operational at this time.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

Performed heater tune-up on a Rheem heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. I did find the indoor coil is leaking refrigerant. The indoor blower wheel is dirty and the outdoor fan motor is leaking oil. Installed new client supplied filter and I recommended replacement every month to prevent extra stress on the system.

Heat check completed on a vertical gas system. Drain line was cleared and treated. Flame sensor was cleaned. All electrical and mechanical components were found within manufacturer specifications. The system is heating properly at time of departure.

Performed heater tune-up on a Carrier furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line. Cleaned the exterior of the air handler and secured outdoor compressor wiring. I did find the fan setting on the thermostat was set to “circulate”. I recommended leaving the setting on “auto” to prevent excess humidity in the home during summertime. No other issues were found. The system is running at completion of service.

Performed heater tune-up on an American Standard heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line. Cleaned the exterior of the air handler and washed the outdoor coil. All surge protection devices and the air purifier are on and working. No major issues were found. The system is operational at this time.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

Performed heater tune-up on a Lennox furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. Replaced the high voltage wire nut with a Wago wire connector. No major issues were found. The system is operational at this time.

Upsized bucket in bedroom and ran new flex duct. Installed top down bucket in back bedroom and attached flex from the sidewall. Upsized duct going back to the bathroom and upsized the bucket. Both systems are operating at this time.

Performed service diagnostic. The diagnostic found that the capacitor on the condenser unit was below value and not starting the compressor. Options for repair were presented to the homeowner and he chose to have the capacitor replaced. I replaced the capacitor on the condenser unit and function tested the system. The system was running at the completion of service.