Kyle TX Heating & Air Conditioning Services

Heat check completed on an upflow furnace. Drain line was cleared and treated. Flame sensor was cleaned. All mechanical and electrical components are within manufacturer specifications. No major issues were found. The system is running at completion of service.

Built and installed new return plenum. Built and installed new supply plenums with existing zoning equipment. Installed 2 new return buckets with filter grills and cut in new supply bucket with new grill in master bedroom. Ran new flex back to the system to match the new buckets. Removed duct from distribution box going to master bedroom and made it home run to the supply plenum. Sealed all ductwork connections with mastic/hardcast. Tested system operation. Everything is working at completion of service.

Heat check completed on a horizontal gas furnace. Drain line was flushed and treated. Flame sensor was cleaned. During maintenance of the furnace, I observed attic air leakage through the supply grills letting attic air into home. No other major issues were found. The system was running at completion of service.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. No major issues were found. The system was running at the completion of service.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filters were replaced with client supplied filters. No major issues were found. The system was running at the completion of service.

Installed 2.5 ton R-454B Payne system. Vertical air handler in hallway closet. New disconnect box for the condenser. Installed new plywood overlay for the air handler to sit on. Built and installed new extended supply plenum. Sealed all ductwork connections with mastic / hardcast. Rebuilt primary condensation drain, added new secondary safety switch. Cleared drain with CO2 and primed trap with water Pressure tested system with nitrogen and pulled vacuum. Cleaned out return chase under the air handler. Charged AC with R-454B refrigerant. Tested heating and cooling operation. Everything is working at completion of install.

Heat check completed on a vertical gas system. Air filter replaced, flame sensor cleaned, and drain line was flushed and treated. I did find that the blower wheel is dirty and recommended cleaning it. No other issues were found. The system is heating properly at this time.

Heat check completed on a horizontal furnace. The flame sensor was cleaned. The drain line was flushed and treated. All electrical and mechanical are within manufacturer specifications. No major issues were found. The system was running at completion of service.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain lines and flow tested the system with two gallons of water. I also treated the drain line. The air filters are clean and had been recently replaced by the homeowner. I did find that part of the flu pipe for the furnace was sagging. I secured the flue pipe so it has a straight run without any sagging. No major issues were found. The system was running at the completion of service.

Performed heater tune-up on a Daikin gas furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. I did find the system is working with high static pressure but due to the location of the system there is no room for improvements. No other issues were found. The system is operational at this time.

Performed heater tune-up on a Goodman 90% gas furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. I did find one of the furnace pvc exhaust pipes had a small crack where it connects at the furnace. This was causing a slow water leak into the furnace. I sealed the crack with silicone and verified it is leak free. No other issues were found. The system is operational at this time.

Heating tune-up for a dual fuel system completed. Drain line was flushed and treated. Flame sensor was cleaned. Outdoor coils were cleaned. I adjusted the gas pressure to the furnace. No other major issues were found. The system is running at completion of service.

Performed heat check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. I replaced the air filter with a new Aprilaire 210 filter. Homeowner also asked me to install a new thermostat that she had purchased. I installed the thermostat and function tested the system in heating and cooling. No major issues were found. The system was operational and running at the completion of service.

erformed heat check on two systems. Checked the electrical, mechanical, safety, and performance of the systems. I cleared the condensation drain lines and flow tested the drains with two gallons of water. I also treated the drain lines. The air filters were clean and had been recently replaced by the homeowner. No major issues were found. The systems were running at the completion of service.

Installed Carrier 3 ton furnace. Installed new plywood overlay. Installed new supply plenum and sealed all connections with mastic. Rebuilt and insulated primary drain line. Cleared drain and verified operation. Installed SS2 safety switch. Replaced disconnect and whip at outdoor system. Reinsulated suction line and ran low voltage in seal tite. Sealed lineset penetration with expanding foam. Tested system and charged to meet manufacturer specifications. Everything is working at completion of service.