Kyle TX Heating & Air Conditioning Services

nstalled 3.5 ton R-454B condenser and evaporator coil. Installed new disconnect box and wiring for the condenser. Installed new Carrier gas furnace. Installed Ecobee Pro thermostat. Installed new secondary drain pan. Built and installed transition for the furnace - coil connection. Rebuilt primary drain and added SS2 / SS3 safety switches. Insulated secondary drain line. New flue pipe and gas pipe connections for the furnace. Sealed all connections with mastic and hardcast. Cleared primary drain with CO2 and primed trap with water. Pressure tested system with nitrogen and pulled vacuum. Charged the system with R-454B refrigerant. Tested heating and cooling operation. Everything is working at completion of install.

Service diagnostic found that the capacitor on the condenser unit had failed. I also found that the capacitor for the blower motor was below value. Options for repair were presented to the homeowners and they chose to have both capacitors replaced. I replaced the condenser capacitor and the blower motor capacitor. I function tested the system and the system was operational. The system was running at the completion of service.

Service diagnostic found that the capacitor on the condenser fan motor had failed. I also found that the condenser fan motor was leaking lubricant. Options for repair were presented to the homeowner and she chose to have the capacitor and condenser fan motor replaced. I replaced the capacitor on the condenser unit as well as the condenser fan motor. I function tested the system and the system is now operational. The system was running at the completion of service.

AC cool check completed on one horizontal Carrier gas system. Drain line has been flushed and treated. Condenser coils have been cleaned. All mechanical and electrical components are within manufacturer specifications. No major issues were found. The system is cooling properly at time of departure.

On arrival, I found that the outdoor fan motor was not spinning. I tried to manual spin the motor but found it was seized up. I checked the run capacitor outside and found it was still within range tolerance. I measured the factory motor and confirmed we would be able to use an aftermarket universal motor as a replacement. I went over repair options with the homeowner and they chose to replace the motor today. I installed an aftermarket condenser fan motor at the outdoor condenser. Set speed and rotation of motor and secured the fan shroud back onto unit. Started up the system and checked over operations. Everything is working at completion of service.

AC cool check completed on one horizontal Lennox system. Drain line was flushed and treated. Condenser coils were cleaned. I found the condenser fan motor leaking lubricant. I presented options for repair to the homeowner and they chose to replace the condenser fan motor at this time. I replaced the condenser fan motor and cycled the system on to verify proper operation. No other major issues were found. The system is running at completion of service.

Service diagnostic found that the condensation drain line was clogged. Water had backed up into the safety switch and shut down the system. I also found that the condenser fan motor had a hot spot on the motor. Options for repair were presented to the homeowner and she chose to have the drain line cleared. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. I function tested the system and clear water was observed flowing out of the drain line. The system was running at the completion of service.

Service diagnostic found that the primary drain line was clogged. I also found the outdoor contactor is pitted. I presented repair options to the homeowner and she chose to have the drain line serviced and the outdoor contactor replaced. I cleared, cleaned, flushed and treated the drain line and verified it is draining outside. I then replaced the outdoor contactor and reset the breaker. All UV lights and surge protection devices are working. The system is operational at completion of service.

Pumped down existing refrigerant into the condenser. Installed new Carrier 2 stage 4 ton R-454B condenser. Replaced liquid line filter drier. Pressure tested system with nitrogen and pulled vacuum. Charged AC with R-454B refrigerant. Tested operation of system. Everything is working at completion of service.

AC cool check completed on one upflow Goodman system. Drain line was flushed and treated. Condenser coils were cleaned. I found the the indoor torque booster below manufacturer specs. I also found the outdoor condenser fan motor showing signs of overheating. No other major issues were found. The system is cooling at completion of service.

Service diagnostic found that the primary drain line was clogged on the downstairs system. The water safety switch was tripped and shut off the outdoor unit. I presented repair options to the homeowner and she chose to have the drain line serviced. I cleaned, flushed and treated the drain line. I then cycled power at the thermostat and verified it is draining outside. No other issues were found. All UV lights and air purifiers are working. The system is operational at this time.

AC cool check completed on one Rheem upflow system. Drain line was flushed and treated. Condensing coils were cleaned. All electrical and mechanical components are within manufacturer specifications. The system is cooling properly at time of departure.

AC cool check completed on a horizontal Payne heat pump. Drain line was flushed and treated. Condenser coils were cleaned. All electrical and mechanical components are within manufacturer specifications. The system is cooling properly at time of departure.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with water. I also treated the drain line. The current air filter is slowing down airflow across the evaporator coil. I let the tenant know he will need to change the filter to prevent issues. Condenser coil was cleaned. No major issues were found. The system was running at the completion of service.

Performed A/C tune-up on a Carrier straight cool system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. Replaced return air filters and washed the outdoor coil. I found there is no water safety switch on the secondary drain and the outdoor fan motor is showing signs of over heating. No other major issues were found. The system is operational at this time.