Kyle TX Heating & Air Conditioning Services

AC cooling maintenance completed on one vertical Carrier system. Drain line was flushed and treated. Condenser coils were cleaned. I found the outdoor torque booster below manufacturer specs. I also found the condenser fan motor showing signs of overheating. I went over my findings and presented repair options to Kathy. She chose to replace the torque booster and condenser fan motor at this visit. I completed the repairs and cycled the system to check proper operation. No other major issues were found. The system is cooling properly at time of departure.

Performed AC cool check and checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. The condenser coil was cleaned. No major issues were found. The system was running at the completion of service.

Performed AC cool check and checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filters are clean and had been recently replaced by the homeowner. I cleaned the condenser coil. No major issues were found. The system was running at the completion of service.

Service diagnostic found that the high voltage wire had melted at the outdoor contactor. I also spoke to Chance about having the drain line serviced. Repair options were presented to homeowner and he chose to just have the contactor replaced today. I replaced the contactor and stripped back new clean wire. I also secured the outdoor compressor wiring and taped the insulation on the door panel at the indoor air handler. I function checked the system. The system is operational at completion of service.

Performed A/C tune-up on a Lennox straight cool system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line. I replaced the high voltage wire nuts with a Wago wire connector. Adjusted the airflow on the system. Washed the outdoor coil and secured the compressor wiring. I also closed off a supply register slightly so the customer is more comfortable in the room by the garage. I did find the outdoor contactor is pitted. No other issues were found. The system is operational at this time.

Pumped down existing refrigerant to the condenser. Installed new TXV metering device. Installed new liquid line filter drier. Pressure tested system with nitrogen and pulled vacuum. Cleared primary drain with CO2 and primed trap with water. Charged the system with R-410A refrigerant. Everything is working at completion of service.

Performed AC cool check and checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. Air filter was replaced with a client supplied filter. Condenser coil was cleaned. No major issues were found. The system was running at the completion of service.

Performed the diagnostic and found that the condensation drain line was clogged. Options for repair were presented to the homeowner, and Karla chose to have the drain line cleared. I cleared the drain line and washed the air filters. I rinsed off the evaporator coil with cleaning solution and tested the system. The system is now operational, and I could see the cleaner draining out of the drain line while the system was running. I allowed the system to run until clear water was flowing tough the drain line.

Upon arrival, the homeowner stated she had water dripping out of her secondary drain line on her front porch. I began the diagnostic and found the emergency drain pan half full of water. Further investigation found that the drain line was clogged. I presented repair options to resolve issue, and they chose to have the drain line cleared today. I removed all the water from the secondary drain pan. The primary drain was then cleared flushed, treated, and primed before departure. System operational at this time.

Service diagnostic found that the system was low on refrigerant. I performed a leak check and found a leak in the evaporator coil. Options for repair were presented to the homeowner and he chose to have refrigerant added to the system. I added two pounds of R-410A to the system and brought the system up to factory specifications. The system was cooling at the completion of service.

Service diagnostic found that the capacitor on the condenser unit had failed. I also found that the condenser fan motor showed signs of overheating. Options for repair were presented to the homeowner and he chose to have the capacitor and the condenser fan motor replaced. I completed the repairs and function tested the system. The system was running at the completion of service.

Installed Carrier gas furnace. Installed Ecobee thermostat. Installed new supply plenum and attached and sealed duct work. Re insulated suction line. Pressure tested and pulled a vacuum on the copper line set. Installed new disconnect and whip at outdoor condenser. Rebuilt and insulated primary drain line. Installed SS2 Safety switch. Cleared drain and verified operation. Charged system to meet specifications. Function checked system. Everything is working at completion of service.

Upon arrival, the homeowner stated for the past couple days the upstairs unit hasn’t been cooling properly and that the indoor system was blowing air just not cold air. I looked over both of the indoor furnaces and found that the first floor unit had no float switch. The primary drain was clogged and water was pouring into the emergency drain pan. I checked the condenser and found a faulty torque booster on the second floor unit, keeping the compressor from turning on. I presented repair options to the homeowner and he chose to replace the torque booster and clear the condensation drain line. I replaced the torque booster and cleared the drain line. I then function tested both systems. Everything is working at completion of service.

AC cool check completed on one upflow Carrier system. I found a clogged drain line and I cleared, flushed, and treated the drain line. Condenser coils were cleaned. I did find the blower wheel dirty and in need of cleaning. I also found the low-voltage wire outside running to condenser to be worn, nicked, and in bad shape. I went over my findings and presented repair options to the homeowner. The system was cooling at time of departure.

Recovered remaining refrigerant charge from system. Disassembled mini split head and cleaned blower wheel and all panels. Installed new evaporator coil and made new flare fitting connection. Pressure tested system with nitrogen and pulled vacuum. Reassembled mini split head components. Weighed in factory charge of R-410A. Tested operation of system. Everything is working at completion of service.