Kyle TX Heating & Air Conditioning Services

Installed new Carrier two stage gas furnace and case coil in attic with outdoor AC. Added new supply and return plenums and installed 210 April air media filter. Rebuilt drain line with SS-2 safety switches and verified their operation. Cleared drain line and tested drainage. Function tested the system in heating and cooling. Everything is working at completion of service.

Service diagnostic found that the capacitor on the condenser unit had failed. I also found that the condenser fan motor showed signs of overheating. Options for repair were presented to the homeowners and they chose to have the capacitor and condenser fan motor replaced. They also chose to sign up for maintenance. I replaced the capacitor and condenser fan motor and function tested the system. I also rinsed off the condenser coil and treated the condenser cabinet with JS insecticide to keep ants away from the contactor. The system was running at the completion of service.

Performed AC cool check. Checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. Air filters are clean and had been recently replaced by the homeowner. I cleaned the condenser coil. Options for system enhancements were presented to the homeowner and Barbara chose to have surge protectors installed on the furnace and condenser units. I installed the surge protectors and function tested the system. No other major issues were found. The system was running at the completion of service.

Pumped down existing refrigerant to the condenser. Installed new evaporator coil with new case. Installed new liquid line filter drier. Pressure tested system with nitrogen and pulled vacuum. Sealed connection to furnace and supply plenum with mastic and hardcast. Rebuilt primary condensation drain and added secondary safety switch. Cleared primary drain with CO2 and primed trap with water. Used shop vac to remove water from secondary pan from when the old evaporator coil had thawed. Charged the system with R-410A refrigerant to 9 degrees subcooling. Tested operation of system. Everything is working at completion of service.

I replaced the outdoor fan motor and programmed it to the correct speed. I then cycled power at the thermostat and function checked the system. The system is working at completion of service.

Installed ductless system on plastic pad. Installed line hide and sealed penetration. Secured drain and tested operation. Reflared line set and pulled a vacuum. Tested system operation. Everything is working at completion of service.

AC cool check completed on horizontal Carrier system. Drain line was flushed and treated. Condenser coils were cleaned. All mechanical and electrical components are within manufacturer specifications. The system is cooling properly at time of departure.

AC cool check completed for one upflow Carrier system. Drain line was flushed and treated. Condenser coils were cleaned. I found the blower wheel with slight buildup, condenser fan motor showing signs of overheating, and the outdoor torque booster well below manufacturer specs. I went over my findings with the homeowner and they chose to replace the torque booster at this time. I replaced the torque booster and function tested the system. No other major issues were found. The system was cooling at time of departure.

Installed Carrier 2 1/2 Ton furnace. Installed Ecobee pro thermostat. Installed new supply plenum. Installed new plywood overlay. Sealed all connections with mastic air lock. Reinsulated suction line. Replaced disconnect and whip. Rebuilt primary drain and insulated. Installed SS2 and tested. Insulated the suction line outside. Checked system pressures to ensure it met manufacturer specifications. Everything is working at completion of service.

AC cool check completed on one horizontal Carrier system. Drain line has been cleared and treated. Condenser coils have been cleaned. I found the blower wheel has a lot of buildup. The condenser unit has a very old contactor. I went over my findings and presented options for repair to the homeowner. No other major issues were found. The system is cooling at completion of service.

Performed A/C tune-up on an American Standard heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned and treated the drain line and washed the outdoor coil. The indoor coil is extremely rusted and could be prone to refrigerant leaks in the future. The system is operational at this time.

Installed 4 ton Carrier furnace. Installed Ecobee pro thermostat. Installed new secondary drain pan. Installed new return and supply plenums and sealed all connections with mastic. Removed wye and upsized duct going back to office and ran them back to the supply. Ran new thermostat wire. Replaced condenser pad and installed new disconnect and whip. Pressure tested line set and pulled a vacuum. Charged system to meet manufacturer specifications Everything is working at this time.

I found the outdoor X13 condenser fan motor had failed. It would run for 3 seconds then shut off for 30 then run again until tripping the high pressure switch. Spoke with the homeowners and they decided to move forward with a replacement outdoor fan motor. I installed a new fan motor and programmed the motor to match speed and rotation of OEM motor. Cycled high voltage power to system and checked over operations. Everything is working at this time.

AC cool check completed on one Carrier system. Drain line was flushed and treated. Condenser coils were cleaned. All electrical and mechanical components working within manufacturer specifications. The system is working at completion of service.

Performed A/C tune-up on a straight cooling system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line. Secured the outdoor compressor wiring and washed the outdoor coil. No major issues were found. The system is operational at this time.