Kyle TX Heating & Air Conditioning Services

Installed new dehumidifier in the attic on top of new platform. Installed drain pan with safety switch for the dehumidifier. Built and installed new extended supply plenum with elbow. Built new drain line tied into the system primary drain. Removed zoning equipment and wires. Sealed all connections with mastic / hardcast. Installed Ecobee thermostat upstairs. Cut new return in for the dehumidifier. Everything is working at completion of service.

AC cool check completed on six-year-old vertical Carrier system. Drain line was cleared, primed, and treated. Condenser coil was cleaned. No major issues were found. The system is cooling properly at time of departure.

Performed AC cool check and checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. Air filter was clean and had been recently replaced by the homeowner. Surge protection was operational. I cleaned the condenser coil. No major issues were found. The system was running at the completion of service.

Performed A/C tune-up on a Carrier straight cooling system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. Replaced the return air filters and washed the outdoor coil. I also replaced the batteries on all 5 smoke detector alarms. I did find the return side of the system has high static. No other issues were found. System was left on 78 per homeowner request.

Performed A/C tune-up on a Carrier heat pump system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the air handler. Secured the compressor wiring and washed the outdoor coil. No major issues were found. The system is operational at this time.

Service diagnostic found that the condensation drain line was clogged. Water had backed up into the secondary drain line and tripped the safety switch. Options for repair were presented to the homeowner. She chose to have the drain line cleared. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. I function tested the system and the system was running at the completion of service.

Service diagnostic found that the primary condensation drain line was clogged. Water had backed up into the safety switch and shut down the system. I also found that the blower motor capacitor was below value. Options for repair were presented to the customer. She chose to have the drain line cleared, the blower motor capacitor replaced and to sign up for maintenance. I cleared the condensation drain line and flow tested the with two gallons of water. A visible clog was blown out of the drain and clear water was observed flowing out of the drain line. I also treated the drain line. I replaced the blower motor capacitor and function tested the system. The system was running at the completion of service.

Performed a diagnostic on the system and found the thermostat display is not working and this is causing the system to run nonstop. I also found the drain line has buildup in it. Lastly, the blower wheel is dirty and there is no water safety switch on the system. I spoke with the homeowner, and she chose to only have the thermostat replaced at this time. I replaced the thermostat and verified that the system is now working. I also secured the compressor wiring at no additional cost.

AC cool check completed on one upflow Carrier system. Drain line was cleared and treated. Condenser coils were cleaned. I found the contactor showing significant signs of wear and tear. I presented options for repair to the homeowner and she decided to replace the contactor today. I removed the old contactor and installed the new one. I function tested the system. No other major issues were found. The system is cooling properly at time of departure.

Installed 3 ton Payne R-454B condenser, Payne gas furnace and evaporator coil Installed Honeywell T6 thermostat. Installed new disconnect box for the condenser. Built and installed new supply plenum. Vacuumed and cleaned the return chase. Sealed all connections with mastic / hardcast. New gas pipe and flue pipe connections for the furnace. Rebuilt primary condensation drain and new safety switch on the secondary. Cleared drain with CO2 and primed trap with water. Pressure tested system with nitrogen and pulled vacuum. Everything operating at completion of service.

AC cool check completed on three year-old Payne horizontal system. Drain line was flushed primed and treated. Condenser coil was cleaned. No major issues were found. The system is cooling properly at time of departure.

Installed 2.5 Ton R-410A Amana heat pump condenser. Installed new disconnect box for the condenser. Leveled new pad for the unit to sit on. Ran the low voltage wires in EMT down the wall into seal tight. Sealed gap on the return plenum to the air handler. Cleared drain with CO2 and primed trap with water. Installed sheet metal hood over lineset and drain wall penetration. Pressure tested system with nitrogen and pulled vacuum. Charged AC with R-410A refrigerant. Tested heating and cooling operation. Everything is working at completion of service.

AC cool check completed on five year-old horizontal Carrier system. Drain line has been cleaned, cleared, and treated. Condenser coils have been cleaned. No major issues were found. The system is cooling properly at time of departure.

Upon arrival, the homeowner stated he had water coming out of his secondary drain line. I went over repair options and he chose to have me clear the drain line. While doing so, homeowner stood near the sink where the condensation line terminates and verified CO2 was getting through the pipe to make sure the drain was cleared. I function tested the system and found no other major issues. The system was cooling properly at time of departure.

Performed AC cool check and checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also tested the drain line. The air filter was replaced with a client supplied filter. I cleaned the condenser coil. No major issues were found. The system was running at the completion of service.