Kyle TX Heating & Air Conditioning Services

AC cool check completed on 11 year-old upflow Carrier heat pump. Drain line was flushed, treated, and primed. Condenser coils were cleaned. All mechanical and electrical components found within manufacturer specs. The system is cooling properly at time of departure.

Performed AC cool check and checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. Air filters were replaced with client supplied filters. Condenser coil was cleaned. No major issues were found. The system was running at the completion of service.

Service diagnostic found that the capacitor on the condenser unit had failed. The contactor for the condenser unit was burnt and pitted and the condenser fan motor showed signs of overheating. Options for repair were presented to the customer and he chose to have the capacitor, contactor and condenser fan motor replaced. I replaced the capacitor, contactor and condenser fan motor and then function tested the system. The system is now operational and was running at the completion of service.

Performed diagnostic on the system and found that the supply air sensor has failed and was causing the system to cycle on and off every 5 minutes. I also found the indoor blower wheel is dirty and the outdoor fan motor has a hotspot. I presented repair options to the homeowner and he chose to have the supply air sensor replaced at this time. I replaced the sensor and watched the operation of the system for 15 minutes. Verified both zones are open and the system is working properly at this time. I did remove the filter to prevent any unwanted stress on the system.

Performed diagnostic on the system and found the outdoor capacitor had failed. I also found the drain line was clogged and the outdoor fan motor is showing signs of wear and tear. I spoke with the homeowner and presented repair options. He chose to have the capacitor replaced and the drain line serviced. I replaced the capacitor and cleared, flushed and treated the drain line. I also replaced the filter for the tenant, washed the outdoor coil and secured the compressor wiring at no additional cost. No other issues were found. The system is operational at this time.

Performed AC cool check and checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was clean and had been recently replaced by the homeowner. Condenser coil was cleaned. No major issues were found. The system was running at the completion of service.

Performed AC cool check and checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was clean and had been recently replaced by the homeowner. The blower wheel was dirty and there was growth found inside the air handler. I cleaned the condenser coil. Options for repair were presented to the customer. No other issues were found and the system was running at the completion of service.

AC cool check completed on vertical carrier heat pump. Drain line was cleared treated and primed. Condenser cool was cleaned. I found the condenser fan motor showing signs of overheating. The torque booster barely within manufacturer specs. There is not currently surge protection on the system. I went over repair options with the homeowners. No other major issues were found. The system was cooling at time of departure.

Performed AC cool check and checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. I cleaned the condenser coil. No major issues were found. The system was running at the completion of service.

Replaced coil. Built new supply plenum and built new transitions. Attached all duct work and sealed with mastic air lock. Cleared drain and verified operation. Hard piped gas line out of furnace and checked for leaks. Pulled vacuum on copper line set. Passed a decay test and charged to manufacturer specifications. Everything is operational at completion of service.

Performed AC cool check and checked the electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a client supplied filter. Both surge protectors are operational. I cleaned the condenser coil. No major issues were found. The system was running at the completion of service.

Built and installed new extended supply plenum. Built and installed new return plenum transition for media filter fitment. Reconnected all existing flex duct. Sealed all connections with mastic / hardcast. Installed new secondary drain pan. Rebuilt primary drain line with proper slope. Installed SS2 and SS3 safety switches. Installed UV light system in evaporator coil and supply plenum. Cleared drain with CO2 and primed trap with water. Tested heating and cooling operation. Everything is working at this time.

AC cool check performed on 10 year-old vertical Carrier system. Drain line was flushed, primed, and treated. Condenser coil was cleaned. I found the blower wheel heavily impacted and the condenser fan motor leaking lubricant. I went over my findings and the homeowner decided to move forward with the repairs today. I picked up a new condenser fan motor and replaced the old one. I then performed the blower wheel cleaning. I cycled the system to verify proper operation. No other major issues were found. The system was running at completion of service.

Performed A/C tune-up on a Carrier heat pump system and a mini split system. Checked the electrical, mechanical and performance systems of both units. Cleared, cleaned, flushed and treated the drain lines and cleaned the exterior of both indoor systems. Washed the mini split filters and both outdoor coils. No issues were found. Both systems are operational at this time.

Installed new dehumidifier in the attic on top of new platform. Installed drain pan with safety switch for the dehumidifier. Built and installed new extended supply plenum with elbow. Built new drain line tied into the system primary drain. Removed zoning equipment and wires. Sealed all connections with mastic / hardcast. Installed Ecobee thermostat upstairs. Cut new return in for the dehumidifier. Everything is working at completion of service.