Kyle TX Heating & Air Conditioning Services

On arrival I found the thermostat at 63 and the heat on. I performed the diagnostic and found that the low voltage fuse was burnt. I used my resettable fuse and started up the system with no issues. I cycled power multiple times at the thermostat, and everything is started and ran properly. I did find that the low-pressure switch wires had a small rub out. I secured the wiring for the pressure switch, and compressor as well, to prevent further rub outs. I also replaced all return air filters.

Performed the heater tune-up on a Carrier gas furnace system. Checked the electrical, mechanical and performance systems of the unit. The homeowner provided air filters and I replaced them for her. I cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. Replaced the high voltage wire nuts with a Wago wire connector. No major issues were found, and the system is operational at this time.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filter was replaced with a customer supplied filter. System sterilizers are operational. The condenser fan motor is showing signs of overheating. No other major issues found, and the system was running at the completion of service.

Service diagnostic found that the air handler was not receiving power. One of the wires used to connect the air handler to incoming power had come loose and melted. Options for repair were presented to the customer, and she chose to have the wires repaired and sign up for our maintenance plan. I cut back the wires to a clean and fresh section of wire. I remade the connections for incoming power and function tested the system. The system was running at the completion of service.

Performed the heater tune-up on a Carrier gas furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. I replaced the high voltage wire nuts with a Wago wire connector. I also removed the drain cap on the p-trap to allow better drainage when the air conditioner is running. No other major issues were found, and the system is operational at this time.

Performed semiannual maintenance on two 2-zone mini split systems. Inspected all Performance, Mechanical and Safety systems. Tested and verified everything was operating within manufacture specifications for operation.

Removed zone dampers and control board. Replaced the supply plenum. Installed new zone dampers. Ran new flex to satellite plenum. Sealed all connections with mastic air lock. Verified system operation. Everything is operating at this time.

Heat check completed on a vertical furnace. No major issues found.

Performed a heater tune-up on two Carrier heat pump systems. Checked the electrical, mechanical and performance systems of the units. Cleared, cleaned, flushed and treated the drain lines and cleaned the exterior of the furnace. Washed both outdoor coils and verified the compressor wiring is secure. I did find that the Ecobee thermostat for the upstairs system is not connected to WiFi. I helped the homeowner set up an Ecobee account and register their thermostat. The Ecobee thermostat now has a WiFi connection and is operational at this time. No other major issues were found. All air purifiers and UV light are working. Both systems are operational at this time.

Installed new Carrier R-454B 4-ton heat pump system. Installed Ecobee Pro thermostat. Installed 25x20 filter base. Installed new supply plenum and sealed all ductwork. Rebuilt and insulated primary drain line. Cleared drain and verified operation. Reinstalled existing UV lights. Replaced disconnect and whip at outdoor unit. Verified system operation.

Heat check completed on a vertical heat pump system. I found that the capacitor for the blower motor is reading below the acceptable range. Also, the condenser fan motor is showing signs of overheating. No other major issues found at this time. The system is heating at departure.

Heat check completed on a horizontal heat pump system. The condenser fan motor is showing signs of overheating and should be monitored. Also, the contactor on the heat pump is showing signs of wear and tear and I would recommend replacement before it fails. No other major issues were found with the system at this time.

Performed a heater tune-up. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air purifier and surge protector are operational. No major issues were found. The system was running at the completion of service.

Heat check completed on a vertical heat pump system. No major issues found, and the system is running at the time of departure.

Performed heat check. Checked electrical, mechanical, safety, and performance of the system. The capacitor for the blower motor is below value, the blower wheel is dirty, the conflation drain line doesn’t have a vent in the drain line to help with the flow of water, and the contactor on the condenser unit is burnt and pitted. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. Options for repair were presented to the homeowner, and he chose to have the blower motor capacitor replaced. I replaced the capacitor for the blower motor and function tested the system. The system was running at the completion of service.