Kyle TX Heating & Air Conditioning Services

Performed the heater tune-up on a Carrier gas furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. I replaced the return air filter for the customer and added a gasket around the filter to help with any filter bypass. I then secured the compressor wiring on the outside unit. No major issues were found, and the system is operational at this time.

Performed semiannual maintenance on one gas furnace heating system. Inspected all Performance, Mechanical and Safety systems. Tested and verified everything was operating within manufacture specifications for operation. Changed out two ceiling filters the homeowner provided for us. Everything is working at this time.

Installed Carrier 3-ton heat pump system. Installed new Ecobee thermostat. Installed new extended supply plenum. Installed new return plenum. Installed new secondary drain pan. Rebuilt and insulated primary drain line. Cleared drain and verified operation. Sealed all connections with mastic air lock. Replaced disconnect and whip at outdoor condensing unit. Reinsulated suction line. Pressure tested line set and pulled a vacuum. Weighed in additional refrigerant to meet manufacture specifications.

On arrival I found both thermostats in cooling mode but the system was not running. I began diagnostic and found the low voltage fuse had blown on the furnace board. I used my resettable fuse and cycled power. As soon as I turned power back on, the transformer had blown and was not working. I replaced the transformer and cycled power again and found that the fuse was blowing when the outdoor condenser would turn on. I went outside and then found the contractor had shorted and was only reading .7 ohms across the coil. I replaced the contactor and cycled power again this time with no issues. I verified both zone dampers are operational as well. I did find the outdoor condenser fan motor is extremely rusted and the secondary drain pan in the attic has a rust spot as well. I spoke with homeowner and presented repair options. She chose to have only the critical components replaced today. System is operational upon completion of repairs.

Performed the heater tune-up on a Carrier gas furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. All UV lights, surge protectors and the air purifier are working. No major issues were found, and the system is operational at this time.

Installed 110k btu Payne gas furnace. Installed new gas flex and connected new Ecco flue pipe. Sealed connections with hardcast and mastic. Tested heating and cooling operation. Gas pressure was set to manufacturer specifications. Cleared condensation drain and tested with water. Also verified temp differential and outdoor electrical values. Everything is operating at this time.

Performed the heater tune-up on a Carrier heat pump system. Checked the electrical, mechanical and performance systems of the unit. The air filter was replaced recently and is still in clean condition. I cleared, cleaned, flushed and treated the drain line. I did find a lot of buildup on the primary pan and cleaned it as best as I could to prevent the drain line from clogging. I ran the system in cooling mode to check refrigerant levels since the outdoor temperature is above 70 degrees. I then washed the outdoor coil. I did find that the blower wheel is dirty. No other major issues were found, and the system is operational at this time.

Performed the heater tune-up on a Carrier gas furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. The air filters were clean. No major issues were found, and the system is operational at this time.

Installed and sealed two new buckets. Removed triangle plenum and made both ducts into home runs. Also verified electrical systems on the indoor and outdoor units were working properly. Cleared drain line and treated with hot water. The system and zones were tested and working at this time.

Heating tune-up completed on a vertical heat pump system. I found that there is a slight buildup on evaporator coil. Due to this, I did visit with the homeowner about increasing the Merv rating and quality of air filter to Merv 8 to prevent further buildup on evaporator coil. The system is heating properly at this time.

Performed heater tune-up on a Goodman gas furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. I replaced the high voltage wire nuts with the right size I found the that filters are dirty. I spoke with homeowner, and he said he would buy some and replace them ASAP. I removed the filters to prevent any further stress on the system. No other major issues were found, and the system is working at this time.

Installed Carrier 3.5-ton system. Installed two new Ecobee thermostats. Installed new supply plenum. Installed new zone dampers, zone board and zone plenum. Installed new return plenum. Sealed all connections with mastic air lock. Replaced secondary drain pan. Rebuilt and insulated primary drain line. Cleared drain and verified operation. Re-piped gas line and gas flex. Installed sediment trap. Replaced disconnect and whip at outdoor condensing unit. Ran low voltage in 1/2-inch Seal-Tite. Re-insulated suction line. Pressure tested and pulled a vacuum on the line set. Weighed in additional refrigerant to meet manufacturer specifications.

Heat check completed on a vertical furnace. No major issues found.

Ran the endoscope camera up the dryer vent and saw multiple feet of blockage. Ran the brush and vacuum the full length of the vent multiple times. Afterwards I ran the endoscope camera again to be sure the blockage was removed.

Installed new return plenum with media filter built in. Installed extended supply plenum. Removed the triangle box and 12-inch flex. Replaced it with a 10x8x8 wye and 8 to 7 reducer. Increased size of bucket and grille going to a bedroom to 12x8x7 with new 7-inch flex. Sealed all connections with mastic. Tested heating and cooling operation.