Kyle TX Heating & Air Conditioning Services

Service diagnostic found that the hot surface igniter has failed. Options for repair were presented to the homeowner, and she chose to have the igniter replaced and to sign up for maintenance. I replaced the hot surface igniter and function tested the system. The furnace came on and ran. The system was running at the completion of service.

Installed new outdoor condenser fan motor and contactor relay switch. Disassembled the blower assembly and cleaned it. While removed, I also cleaned out the furnace, all burners, and the inducer. Assembled everything back together. Completed performance and safety testing. Everything is working at this time.

I removed the dryer and disconnected the flexible exhaust tube. I then ran the camera through the dryer vent to access the clogs. I then proceeded to brush and vacuum out the length of the dryer vent. I ran the camera afterwards to ensure that there weren’t any clogs left. I cleaned out and rerouted the flexible exhaust tube. I then hooked everything back up and tested the dryer.

Performed heat check on two systems. Checked electrical, mechanical, safety, and performance of the systems. I cleared the drain lines and flow tested them with water. I also treated the drain lines. The air filters were replaced with customer supplied filters. No major issues were found. Both systems were running at the completion of service.

I replaced the outdoor condenser fan motor, capacitor and contactor. While replacing the fan motor I removed the leaves inside the condenser unit, washed the outdoor coil and secured the compressor wiring at no extra charge. After I completed the work, I cycled power at the thermostat and verified that the system is now operational.

Installed vertical gas system with R-454B condenser and evaporator coil. Installed new supply plenum. Sealed all connections with mastic. Installed new plywood overlay. Installed new filter grille. Upsized supply bucket and duct going to front bedroom. Installed new gas flex and flue pipe connection. Installed new disconnect and whip for condenser. Pressure tested system with nitrogen and pulled vacuum. Installed new Honeywell T6 thermostat. Cleared condensation drain with CO2 and tested with water. Tested heating and cooling operation.

Performed heater check. Checked electrical, mechanical, safety, and performance of the system. I cleared the condensation drain line and flow tested the drain with two gallons of water. I also treated the drain line. The system did not have a filter installed in the filter grille. No other major issues were found, and the system was running at the completion of service

Performed a diagnostic on the upstairs furnace (manufactured in 2000). I found that the ignitor has failed and is not heating up to ignite the gas furnace. I spoke with homeowner and presented options for repair. He chose to have the ignitor replaced at this time. I replaced the ignitor and verified gas pressure. I also cleaned the flame sensor at no extra charge. The system is now operational.

I arrived to find the thermostat blank. Began the diagnostic by checking the float switch on up-flow air handler. I found that it was tripped due to water backing up in the drain. Presented repair options to the homeowner and they have agreed to have primary drain line flushed cleared and treated. Once the system was up and running, I also looked at the outdoor heat pump unit and found the capacitor well below manufacturer specs. I also found that the condenser fan motor has overheated but is still working. Presented my findings to the homeowner and they approved changing out of capacitor. I replaced the capacitor and function checked the system. The system is running at the time of departure.

Heating tune-up completed on a vertical furnace. I found that the blower wheel is dirty. The gas valve was adjusted for optimal performance. No other major issues found, and the system is heating properly at this time

Performed the heater tune-up on a Carrier gas furnace system. Checked the electrical, mechanical and performance systems of the unit. Cleared, cleaned, flushed and treated the drain line and cleaned the exterior of the furnace. The filter was replaced recently by homeowner. I sealed around the filter to prevent any filter bypass. I also replaced the insulation on the suction line at the outdoor unit since it was deteriorating. No other major issues were found, and the system is operational at this time

Heating check completed on a horizontal furnace. No major issues found.

Performed heater check. Checked electrical, mechanical, safety, and performance of the system. I cleared the drain line and flow tested the drain with two gallons of water. I also treated the drain line. The air filters were replaced earlier this week and still in clean condition. No major issues were found. The system was running at the completion of service.

Service diagnostic found that the capacitor for the condenser fan motor had failed. The condenser fan motor is also showing signs of overheating. Options for repair were presented to the homeowners, and they chose to have the capacitor, and the condenser fan motor replaced. They also signed up for maintenance. I replaced the condenser capacitor and the condenser fan motor. I function tested the system and the system is now operational.