Kyle TX Heating & Air Conditioning Services

Installed Carrier gas system. Installed Ecobee thermostat. Built new supply plenum and return plenums and sealed all connections with mastic. Completed re-duct with new buckets and flex. Sealed all the buckets to the drywall. Replaced secondary drain pan. Rebuilt and insulated primary and secondary drain lines. Cleared, treated and verified drain operation. Installed SS2 and SS3 safety switches. Replaced disconnect and whip at outdoor unit. Ran low voltage in 1/2-inch Seal-Tite. Charged system to manufacture specifications.

I arrived at the home to find the system off. I spoke to customer about how the unit had been performing. I checked over the system and discovered that the blower wheel had pulled apart and that has caused the motor to be off balance. Also, one of the legs of the motor broke from the extreme vibration. I brought all of this to the attention of the customer and made him an option to get it repaired. He elected to move forward with the repairs. I replaced the capacitor as well as the blower motor and blower wheel. I tested the system and found it to be working. The downstairs area is cooling now. System is in working order at completion of appointment.

I arrived at the home to find the system off. I spoke to customer about how the unit had been performing. I checked over the system and discovered that the blower wheel had pulled apart and that has caused the motor to be off balance. Also, one of the legs of the motor broke from the extreme vibration. I brought all of this to the attention of the customer and made him an option to get it repaired. He elected to move forward with the repairs. I replaced the capacitor as well as the blower motor and blower wheel. I tested the system and found it to be working. The downstairs area is cooling now. System is in working order at completion of appointment.

I arrived at the home to find the system off. I spoke to customer about how the unit had been performing. I checked over the system and discovered that the blower wheel had pulled apart and that has caused the motor to be off balance. Also, one of the legs of the motor broke from the extreme vibration. I brought all of this to the attention of the customer and made him an option to get it repaired. He elected to move forward with the repairs. I replaced the capacitor as well as the blower motor and blower wheel. I tested the system and found it to be working. The downstairs area is cooling now. System is in working order at completion of appointment.

I arrived at the home to find the system off. I spoke to customer about how the unit had been performing. I checked over the system and discovered that the blower wheel had pulled apart and that has caused the motor to be off balance. Also, one of the legs of the motor broke from the extreme vibration. I brought all of this to the attention of the customer and made him an option to get it repaired. He elected to move forward with the repairs. I replaced the capacitor as well as the blower motor and blower wheel. I tested the system and found it to be working. The downstairs area is cooling now. System is in working order at completion of appointment.

Performed cooling maintenance on one system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. I found that one of the connector’s terminals on the capacitor was starting to burn up. I stripped back new wire and replaced the connector. The hard start kit was not mounted correctly, so I remounted the kit to prevent any problems in the near future. I also found that the system is slightly low on R-22 refrigerant. The high voltage wire nuts are undersized at the furnace. I replaced the wire nuts at the furnaces and informed the homeowner of my findings. No other major issues found.

Cool check completed on a horizontal heat pump system. The outside coils have been cleaned and all electrical within manufacture specs. Refrigerant charge does have low superheat, but temperature differential is 20°. The indoor coil and blower motor are both clean. One of the float switches has failed. I recommend a p-trap be added to the drain line for proper drainage. I also found that the supply plenum has partially detached and there is leakage around the ducts attached to the supply plenum. No other major issues found.

On arrival the homeowner stated that his outdoor unit was not turning on so he turned the system off at the thermostat. I turned the system on at the thermostat and everything came on. I checked through the system and found that the primary drain line is clogged tripping the water safety switch which is shutting off the outdoor unit, and the return air filter is stuck on the underside of the coil. I removed the filter. I also found that the evaporator coil is dirty, there is mildew growth inside the air handler, there is no water safety switch on the secondary drain line, and the outdoor condenser fan motor is also leaking lubricant. I presented my findings to the homeowner, and he chose to have the drain line cleared at this time. I cleared and treated the drain and then tested it with two gallons of water. System is draining properly and operational at this time.

Cool check completed on a horizontal heat pump system. The indoor coil and fan are both clean. The emergency drain pan underneath the air handler is showing significant signs of rust and I recommend replacing it. The drain line was cleared and both float switches are working. The condenser coil has been cleaned and all electrical within manufacture specs. The refrigerant charge is within range. Added new locking caps on the condenser. No other major issues found.

Installed new evaporator coil. Rebuilt the condensation drain. Cleared, flushed and treated the drain to confirm proper drainage. Replaced the in-line filter dryer, pressure tested with dry nitrogen and pulled a vacuum on copper line set. Charged and tested the system. The system is working properly at this time.

Installed Carrier gas system. Used homeowner’s thermostat. Built new supply plenum and sealed all connections with mastic. Installed plywood overlay. Rebuilt and insulated primary drain line. Cleared, treated and verified drain operation. Installed SS2 safety float switch. Replaced disconnect and whip at outdoor unit. Moved outside condenser over because pad was very un-level. Ran low voltage in 1/2-inch Seal-Tite. Verified charge was to manufacture specifications. System operational at this time.

On arrival I found the system off at the thermostat. I spoke with the customer, and he stated that the system was only blowing hot air. I performed a diagnostic on the system and found that the outdoor capacitor has fallen below value on the herm side. It was reading 2.9 mfd and it is rated for 45 mfd. I informed the customer, and he chose to have the capacitor replaced at this time. I replaced the capacitor and cycled power at the thermostat. No other major issues were found, and the system is operational at this time.

Cool check completed. The drain line was cleared and treated. The float switch was checked and is operational. No issues found with the components for operation of the system. I did find a supply duct run to the master bedroom has been split in two. Presented my findings to the homeowner and they approved the repair. Completed repair and cycled the system to ensure repair and proper air flow to the bedroom.

Installed new 3-ton Carrier gas system. Installed new Honeywell T6 thermostat. Rebuilt and insulated condensate drain line. Added SS2 safety float switch. Cleared drain line with CO2 and ran three gallons of water to ensure proper operation. I then followed that with Viper drain treatment. Installed new filter dryer, pressure tested with dry nitrogen and pulled a vacuum on copper line set. Replace the condenser pad. Replaced the disconnect and ran the low voltage in Seal-Tite. Replaced supply plenums, sealed with a mastic airlock and reused zoning equipment. Charged system to factory spec and performed a benchmark. The system is working properly at time of departure.

Installed Carrier system. Installed Ecobee thermostat. Transitioned to supply plenum and sealed all connections with mastic. Installed plywood overlay. Rebuilt and insulated primary drain line. Cleared, treated, and verified drain operation. Installed SS2 safety float switch. Replaced disconnect and whip at outdoor unit. Ran low voltage in 1/2-inch Seal-Tite. Charged system to manufacture specifications.