Kyle TX Heating & Air Conditioning Services

Performed cooling maintenance on one system. Checked all electrical, mechanical and performance of the system. Cleared and treated drain line and washed the outdoor coil. I found that the secondary drain pan has a rust spot on it, the condenser fan motor is leaking lubricant, and the starter is burnt and pitted at the contacts. I presented my findings to the homeowner, and she chose to have the starter replaced today. The starter was replaced, and the system is operational at this time. .

Cool check completed on a horizontal gas system. The drain line was cleared and treated. The float switch was checked and is operational. The blower assembly is clean. The condenser coil was cleaned. All electrical within range except for the capacitor which is below value. Refrigerant levels within spec. I presented options to have the capacitor replaced and the homeowner agreed. After replacing the capacitor, I cycled the thermostat. The system is cooling properly at this time.

Installed new Payne 4-ton gas system. Rebuilt and insulated condensate drain line. Added SS2 safety float switch. Cleared drain line with CO2 and ran three gallons of water to ensure proper operation. That was then followed by Viper drain treatment. Installed new filter dryer, pressure tested with dry nitrogen and pulled a vacuum on copper line set. Replace the condenser pad. Replaced the disconnect and ran the low voltage in Seal-Tite. Replaced supply plenum and sealed with a mastic airlock. Charged system to factory spec and performed a benchmark. System is working properly at time of departure.

On arrival I found the system off and the homeowner stated that the outdoor unit was not working. Performed diagnostic and found a clog in the primary drain which has tripped the water safety switch and shut down the outdoor unit. I poured water in the primary pan and used my vacuum to get rid of the clog. I also cleared the drain with CO2 and tested it with two gallons of water. I then ran the system and confirmed it is now draining properly. Thermostat was set to 78 per customer request. No other major issues were found, and the system is operational at this time.

Cool check completed on a vertical gas system. The drain line was cleared and treated. The float switch was checked and is operational. I did find some buildup on the blower wheel and informed the homeowner. The condenser coil was cleaned, and the refrigerant level is adequate. The capacitor is within range. Unit is cooling properly at this time. Customer requested thermostat set at 78°.

Repaired leak at outdoor 3/8 service port. After completing the repair, we added 3lbs of R-410A refrigerant. Verified system operation and everything is working at this time.

Tune-up completed on a vertical gas system. The drain line has been cleared. The float switch was checked and is operational. The blower motor has gathered some excess dust and debris. The outdoor coils were cleaned, and all electrical within manufacture specs. Refrigerant level within spec. The condenser fan motor is showing signs of overheating. No other major issues found.

Installed new evaporator cased coil in attic. Rebuilt drain line with SS-2 safety switch. Cleared drain line. Removed the dryer from outside and installed a new one at the coil. Sealed case with tape and air lock. Weighed in 2lbs of refrigerant per factory charge. System operating at this time.

Service diagnostic found that the capacitor for the blower motor has failed. The capacitor was bulged and read 0mfd. Options for repair were presented to the customer, and he chose to have the capacitor replaced. I replaced the capacitor and function checked the system. The system was running at the time of departure.

Service diagnostic found that the capacitor for the blower motor has failed. The capacitor was bulged and read 0mfd. Options for repair were presented to the customer, and Michael chose to have the capacitor replaced. I replaced the capacitor and function checked the system. The system was running at the time of departure.

Service diagnostic found that the capacitor on the condenser unit has failed. Options for repair were presented to the customer, and Stephanie chose to have the capacitor replaced today. Repair was completed and the thermostat was cycled. The system is running at the time of departure.

Service diagnostic found that the thermostat has failed. Options for repair were presented to the customer, and she chose to have the thermostat replaced today. I replaced the thermostat and function checked the system. The system was running at the time of departure.

I arrived at the home to find the system running and the indoor temp is 67 degrees. I checked over the unit and discovered that there is a clog in between the float switch and the outlet of the primary drain at the evaporator coil. I brought this to the attention of Robert and made him an option to get it cleared. He elected to move forward with that repair. I got the drain line cleared. I also installed a union in the drain so it can be removed easier for service in the future. I treated the drain as well. I performed the cooling check while I was here today. Everything else in the system looks to be operating properly. I had no other recommendations to make. System is in working order at completion of appointment

I arrived at the home to find the system running and the indoor temp is 67 degrees. I checked over the unit and discovered that there is a clog in between the float switch and the outlet of the primary drain at the evaporator coil. I brought this to the attention of Robert and made him an option to get it cleared. He elected to move forward with that repair. I got the drain line cleared. I also installed a union in the drain so it can be removed easier for service in the future. I treated the drain as well. I performed the cooling check while I was here today. Everything else in the system looks to be operating properly. I had no other recommendations to make. System is in working order at completion of appointment

I arrived at the home to find the system running and the indoor temp is 67 degrees. I checked over the unit and discovered that there is a clog in between the float switch and the outlet of the primary drain at the evaporator coil. I brought this to the attention of Robert and made him an option to get it cleared. He elected to move forward with that repair. I got the drain line cleared. I also installed a union in the drain so it can be removed easier for service in the future. I treated the drain as well. I performed the cooling check while I was here today. Everything else in the system looks to be operating properly. I had no other recommendations to make. System is in working order at completion of appointment