Kyle TX Heating & Air Conditioning Services

I arrived at the home to find the system on and running. I spoke to Baylor about how the unit had been operating. I checked over the system and discovered a pinhole leak on the liquid line coming out of the filter drier. I brought this to the attention of Baylor and made him an option to get it fixed. He elected to move forward with the work. Details of the work performed today are below: “Includes repair of the leak and 1 pound of refrigerant. Also includes additional refrigerant needed for the system (3 pounds).” I got to work and got the leak patched. I pressure tested the system and also pulled a vacuum to sub 500 microns. I performed a decay test and the system passed. I charged the system with up with 4 total pounds of refrigerant. System is in working order at completion of appointment

Performed cooling maintenance on a straight cool system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. Customer replaced both filters before my arrival. Both surge protectors are on and working. No major issues were found, and the system is operational at this time.

Cool check completed on a horizontal gas system. The drain line was cleared and treated. The float switch was checked and is operational. The blower motor and control board are in good shape. The outdoor condenser was cleaned, and all electrical is within manufacture specs. I did find the system to have a high superheat and normal sub cool with high suction line temperature. Attempted to add a pound of refrigerant to drop superheat which had very little effect. Further diagnosis found a failing TXV. Also verified there is a leak in the evaporator coil.

Cool check completed on a vertical gas system. The system is 18 years old. The drain line was cleared and treated. The float switch was checked and is operational. The condenser coils were cleaned. The capacitor is within value. Areas of concern are as follows: the blower motor leaking lubricant, the contactor needs to be replaced, the condenser fan motor is drawing high amps, and the refrigerant level is slightly low. No other major issues found.

I checked over the system and discovered the following: both blower wheels are dirty, the bigger head unit has a motor that has noisy bearings, and the drain line was clogged on the smaller head unit. I brought all of this to the attention of the homeowner and made him a few options. He elected to move forward with my mid-range option. I went ahead and got the drain lines cleared. I removed and cleaned the blower wheel on the bigger head unit. I then replaced the blower motor. I reassembled everything and tested the system. Everything came on fine. I then removed the blower wheel on the smaller unit and got it cleaned and reinstalled. Both head units are now blowing a lot more air and are working well. The temp is coming down inside the space. System is in working order at completion of appointment.

I checked over the system and discovered the following: both blower wheels are dirty, the bigger head unit has a motor that has noisy bearings, and the drain line was clogged on the smaller head unit. I brought all of this to the attention of the homeowner and made him a few options. He elected to move forward with my mid-range option. I went ahead and got the drain lines cleared. I removed and cleaned the blower wheel on the bigger head unit. I then replaced the blower motor. I reassembled everything and tested the system. Everything came on fine. I then removed the blower wheel on the smaller unit and got it cleaned and reinstalled. Both head units are now blowing a lot more air and are working well. The temp is coming down inside the space. System is in working order at completion of appointment.

I checked over the system and discovered the following: both blower wheels are dirty, the bigger head unit has a motor that has noisy bearings, and the drain line was clogged on the smaller head unit. I brought all of this to the attention of the homeowner and made him a few options. He elected to move forward with my mid-range option. I went ahead and got the drain lines cleared. I removed and cleaned the blower wheel on the bigger head unit. I then replaced the blower motor. I reassembled everything and tested the system. Everything came on fine. I then removed the blower wheel on the smaller unit and got it cleaned and reinstalled. Both head units are now blowing a lot more air and are working well. The temp is coming down inside the space. System is in working order at completion of appointment.

I checked over the system and discovered the following: both blower wheels are dirty, the bigger head unit has a motor that has noisy bearings, and the drain line was clogged on the smaller head unit. I brought all of this to the attention of the homeowner and made him a few options. He elected to move forward with my mid-range option. I went ahead and got the drain lines cleared. I removed and cleaned the blower wheel on the bigger head unit. I then replaced the blower motor. I reassembled everything and tested the system. Everything came on fine. I then removed the blower wheel on the smaller unit and got it cleaned and reinstalled. Both head units are now blowing a lot more air and are working well. The temp is coming down inside the space. System is in working order at completion of appointment.

On arrival the customer stated that his outdoor unit was not running. I performed a diagnostic on the system and found that the primary drain line was clogged. The drain runs into the bathtub drainage. I presented my findings to the homeowner, and he chose to have the drain cleared today. I cleared and treated the drain line and tested it with two gallons of water. I then treated the drain line. No other major issues were found, and the system is operational at this time.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. The air handler, evaporator coil and blower wheel are all clean. The wiring is tight and in good condition. The condenser fan motor is showing signs of overheating. The capacitor for the condenser unit is within value. The contactor is in good condition, and the refrigerant charge is within factory specifications. Options for repair were presented to the customer, and they chose to have the condenser fan motor replaced today. I replaced the condenser fan motor and function checked the system. The system is running at the time of departure.

Spoke with the homeowner and they stated that they noticed water was dripping out the eave of the home. Performed diagnostic and found water in the secondary drain pan due to a clogged drain. Cleared the drain line that was running into bathroom sink. I then flushed the drain line with hot water and drain treatment. The drain is now freely flowing.

Installed Carrier 3 1/2-ton gas system. Installed Ecobee Pro thermostat. Installed new supply and return plenums and sealed all connections with mastic air lock. Ran new thermostat wire. Replaced secondary drain pan. Rebuilt and insulated primary and secondary condensate drain lines. Cleared drain line and verified operation. Installed SS2 and SS3 safety float switches. Replaced disconnect and whip at outdoor condenser. Pressure tested with nitrogen and pulled a vacuum on the line set. Weighed in charge to meet manufacturers specifications. Changed breaker.

Upon arrival I found system on and running. I spoke to homeowner about how the unit had been performing. I checked over the system and discovered that the drain line was clogged. The float switch was also installed incorrectly. I went outside and found that the drain tube was buried under the ground. I picked it up and immediately all of the water rushed out. I made the customer an option to replace the float switch and she elected to move forward. I collected for the work and replaced the float switch. I tested it 3 times and it is now working properly. System is in working order at completion of appointment.

Upon arrival I found system on and running. I spoke to homeowner about how the unit had been performing. I checked over the system and discovered that the drain line was clogged. The float switch was also installed incorrectly. I went outside and found that the drain tube was buried under the ground. I picked it up and immediately all of the water rushed out. I made the customer an option to replace the float switch and she elected to move forward. I collected for the work and replaced the float switch. I tested it 3 times and it is now working properly. System is in working order at completion of appointment.

Upon arrival I found system on and running. I spoke to homeowner about how the unit had been performing. I checked over the system and discovered that the drain line was clogged. The float switch was also installed incorrectly. I went outside and found that the drain tube was buried under the ground. I picked it up and immediately all of the water rushed out. I made the customer an option to replace the float switch and she elected to move forward. I collected for the work and replaced the float switch. I tested it 3 times and it is now working properly. System is in working order at completion of appointment.