Kyle TX Heating & Air Conditioning Services

Service diagnostic found that the condensate drain line has clogged. The secondary drain line is also not level which could cause water to flow back out of the secondary and spill out of the pan. Options for repair were presented to the customer and they chose to have the drain line cleared and to move the drain line so that if water flows into the secondary it will reliably shut down the system. Repairs have been completed and the system is operational.

Replaced the condenser fan motor and cleaned the evaporator coil in place. The system was function checked and was running at the time of departure.

Performed cooling maintenance on one straight cooling system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. Customer had replaced the filter before my arrival. I did find the high voltage wire nuts at the furnace and at the outdoor condenser were undersized. I replaced them and reset the breaker. No other major issues were found, and the system is operational at this time.

Performed cooling maintenance on one heat pump system. Checked all electrical mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. No other major issues were found, and the system is operational at this time.

Service diagnostic found that the drain line is clogged. Water has backed up and tripped the safety switch shutting down the system. There is a large amount of buildup where the drain line connects to the primary pan. I cleared the drain and the buildup at the connection. I then flow tested the drain with water and treated the drain. The system was running at the time of departure.

Performed AC cool check. Checked electrical, mechanical, safety and performance of the system. The blower wheel is clean. The drain line was cleared and treated; a significant amount of buildup was blown out of the drain line. I showed the customer where to treat the drain, as well as how often, to help with future buildup. Condenser coil clean. Condenser fan motor and contactor are in good condition. Refrigerant charge is within factory specifications and is cooling at 10 degrees of sub cooling. The capacitor for the condenser unit has failed on the herm/compressor terminal and the system is running completely off the start assist kit. Options for repair were presented to the customer and they chose to have the capacitor replaced today. I replaced the capacitor on the condenser unit and function checked the system. The system is running at the time of departure.

Performed diagnostic. I found that the outdoor condenser fan motor is not working. I confirmed there’s 240 volts and the capacitor is within range. I presented my findings to the homeowner, and she chose to have the motor replaced at this time. I rinsed the outdoor unit to ensure the coils were clean. I replaced the motor and cycled power at the thermostat. The system is operating at this time with 8 degrees of subcooling and 15 degrees temperature split.

Performed cooling maintenance on one heat pump system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. Filter was replaced recently by the homeowner. No major issues were found, and the system is operational at this time.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. The wiring is tight and in good condition. The blower wheel is clean. The condenser fan motor and contactor are in good condition. The refrigerant charge is within factory specifications. The capacitor for the condenser unit is below value. The condenser coil was cleaned. Options for repair were presented to the homeowner and they chose to have the capacitor replaced today. I replaced the capacitor on the condenser unit and function checked the system. The system is running at the time of departure.

Performed the semiannual maintenance on one inverter driven straight electric AC unit. Inspected all Performance, Mechanical and Safety Systems. I went through the system outside and verified all wiring was properly positioned and secured. I noticed the outdoor coil had some dirt and dust build up so I went ahead and proceeded with the regular maintenance of the unit. I washed the outdoor coil out and removed all leaves from the base pan. Ensured the outdoor surge protection device was on and green lit. Flushed and treated the primary drain line as well. Verified everything was working within manufacture’s specifications for operation. Everything is working at this time.

Cool check completed on a horizontal gas system. The indoor capacitor is outside of manufacture specs. The evaporator coil is showing significant signs of rust. The drain line has been cleared and treated. The float switches were checked and are operational. The outdoor condenser coils are clean. The outdoor capacitor is outside of manufacture specs. The condenser fan motor is leaking lubricant. The refrigerant is low on charge. Presented my findings to the homeowner and they have opted to have both capacitors replaced and refrigerant added at this time. Completed all repairs and the system is cooling properly at time of departure.

Sweated out the old compressor. Brazed in new filter dryer upstairs. Brazed in new compressor. Mounted and connected the ICM. Pressure and vacuum tested. Charged with refrigerant to 8 degrees subcooling. System operational at time of departure.

On arrival the customer stated that there was water dripping outside her home from the secondary drain line of her air conditioner. I poured half a gallon of water in the primary drain line to see if it was draining. I confirmed there is a clog in the primary drain line which is causing water to back up and drain out the secondary drain. I cleared the drain clog and tested the line with 2 gallons of water. I then treated the drain line. I ran the system for 15 minutes and confirmed the water was not backing up anymore. No other major issues were found and the system is operational at this time.

Performed cooling maintenance on one straight cool system. Checked electrical, mechanical and performance of the system. Cleared and treated the drain line washed the outdoor coil. I replaced the high-voltage wire nuts at the furnace which were undersized. I also found that the Seal-Tite for the condenser fan motor wiring wasn’t covering the wiring completely. I fixed the Seal-Tite to prevent any water from damaging the electrical wiring. No other major issues were found, and the system is operational at this time.

Performed cooling maintenance on a straight cool system. Checked all electrical mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. Customer supplied filter for replacement. No major issues were found, and the system is operational at this time.