Kyle TX Heating & Air Conditioning Services

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The air handler and blower wheel are clean. The drain line was cleared and treated. The wiring is tight and in good condition. The condenser fan motor is showing signs of overheating. The contactor is in good condition. The refrigerant charge is within factory specifications. Condenser capacitor is within value. Condenser coil was cleaned. No other major issues were found.

Arrived for a two-system cool check. Upstairs System - Found blower capacitor leaking oil. The condensation line has been cleared and treated. Safety switches checked and are operational. Outdoor condensing coil clean. Capacitor and contactor within range. Refrigerant levels adequate. Condenser fan motor is leaking grease. Downstairs System - Found blower motor leaking grease and showing signs of overheating. The condensation line has been cleared and treated. Safety switches checked and are operational. Outdoor condenser electrical within manufacture specs. Found downstairs refrigerant levels below range. After discussing repair options with the customer, he has chosen to have the upstairs blower motor capacitor replaced. He has also opted to have refrigerant added to the downstairs unit. Lastly, he chose to have the upstairs condenser fan motor replaced. Completed repairs and both systems are operational.

I charged the system with refrigerant to bring it up to factory specifications. 3lbs of R-410A was added. The sub cooling is now 10 degrees. The temperature split is 19 degrees. System was running at the time of departure.

Single system cool check completed on a gas system. The upstairs unit is clean, and the air filter has been changed. The float switch was checked and is working properly. The drain line has been cleared and treated. Outside condensing coils clean. Amp draws within range. All electrical within manufacture specs. Checked temperature differential and it was within range. The system is operating properly at this time.

Single system cool check completed. The indoor furnace was checked for cleanliness and amp draws are within range. The condensation drain line was cleared and treated. The float switch was checked and is operating properly. Outdoor coils have been cleaned. Fan and compressor amps are within range. I did find the capacitor is well below manufacture specs. Also, the refrigerant levels are slightly low giving a 15° temperature split. Inspected the outside system for leaks where oil residue was found and was able to detect a leak coming from liquid line service valve. Presented repair options and the homeowners decided to have the capacitor replaced. Replaced the capacitor and function checked the system. Everything is currently operational.

Single system cool check was performed on a gas system. The furnace is clean with no buildup found. Drain lines cleared and treated. Both float switches checked and are operational. Both air filters have been changed. Outdoor condensing coil clean. All electrical within manufacture specs. Refrigerant level good. No major issues found, and the system is operating properly at this time.

nstalled 5-ton Carrier heat pump system. Installed Ecobee thermostat. Installed plywood overlay for system. Transitioned to existing supply plenum. Rebuilt and insulated primary drain line. Installed SS2 safety float switch. Cleared drain and verified operation. Replaced disconnect and ran both high and low voltage in new Seal-Tite. Installed new UV shield. Installed air purifier. Pressure tested and pulled a vacuum on the copper line set. Weighed in charge to meet manufacturers specifications.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. The air handler and evaporator coil are clean. The blower wheel is also clean. The wiring is tight and in good condition. Condenser coil clean. The condenser fan motor is in good condition. Refrigerant charge is within factory specifications. Surge protection for both sides of the system are operational. No major issues were found. The system was running at the time of departure.

Replaced the indoor evaporator coil. Replaced the inline filter dryer, pressure tested with dry nitrogen and pulled a vacuum on copper line set. Rebuilt condensate drain and added SS2 safety float switch. Cleared and treated the condensate drain. Charged system to factory specs and checked operation of the system. The system is working properly at this time

I rinsed out the outdoor coil, cleared and treated the drain. I checked over the system and discovered the following: the evaporator coil is leaking refrigerant, the condenser fan motor is leaking oil and overamping, and the defrost control board is showing signs of overheating around the central resistors. I brought all of this to the attention of the customer and made her a few options. System is working to the best of its ability at completion of appointment.

I rinsed out the outdoor coil, cleared and treated the drain. I checked over the system and discovered the following: the evaporator coil is leaking refrigerant, the condenser fan motor is leaking oil and overamping, and the defrost control board is showing signs of overheating around the central resistors. I brought all of this to the attention of the customer and made her a few options. System is working to the best of its ability at completion of appointment.

I rinsed out the outdoor coil, cleared and treated the drain. I checked over the system and discovered the following: the evaporator coil is leaking refrigerant, the condenser fan motor is leaking oil and overamping, and the defrost control board is showing signs of overheating around the central resistors. I brought all of this to the attention of the customer and made her a few options. System is working to the best of its ability at completion of appointment.

I rinsed out the outdoor coil, cleared and treated the drain. I checked over the system and discovered the following: the evaporator coil is leaking refrigerant, the condenser fan motor is leaking oil and overamping, and the defrost control board is showing signs of overheating around the central resistors. I brought all of this to the attention of the customer and made her a few options. System is working to the best of its ability at completion of appointment.

Replaced the mini split coil in the living room. Pressure tested with dry nitrogen and pulled a vacuum on copper line set. Charged system to factory specs and teat operation. The system is working properly at this time.

On arrival, the customer informed me that his outdoor fan motor was not running. I performed a diagnostic on the system and found that some of the wires from the motor had hit the fan blade causing them to be cut. I fixed the wire connection and reset the breaker, but the motor was not functioning and also had grease on the shaft. Presented my findings to the customer and they chose to have the motor replaced today and join our maintenance plan. I replaced the motor and cycled power. No other major issues were found. System is operational at this time.