Kyle TX Heating & Air Conditioning Services

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. The blower wheel is clean. The wiring in the furnace is tight and in good condition. I found a loose low voltage wire at the contactor in the condenser unit. I remade a tight connection with a fresh wire nut. The condenser capacitor is within value and the refrigerant is within factory specifications. The system was shutting down due to the zone control board losing the Y signal. When I checked the zone controls, I found that the supply air sensor is bad and shutting down the condenser. I found an unused/new supply air sensor in the box for the zone control board. I swapped out the old sensor for the new one and the system is running. No other major issues found.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. Drain line was cleared and treated. Filter was changed with a customer supplied filter. The blower wheel is clean. Electrical wiring is tight and in good condition. Condenser coil clean. The contractor and condenser fan motor are in good condition. Capacitor for the condenser unit is within value. The refrigerant charge was within factory specifications. Disconnect is in good condition. No major issues were found.

Single system cooling check completed on an up-flow gas system. Checked interior for cleanliness. Blower wheel does have significant buildup. Also checked amp draws and they are within normal range. The drain line has been cleared and treated. The float switches were checked and are operational. Outdoor condenser coils cleaned. Refrigerant levels within range. All electrical also within manufacture specs. I did find that the contactor is showing severe signs of wear and tear. Presented options to have the contactor replaced and the blower housing cleaned. The customer has chosen to move forward with contactor replacement only. Replaced the contactor and function checked the system.

Single system cool check completed on a horizontal gas system. Amp draws are within range. Float switches check and are working properly. Drain lines have been cleared and treated. Condenser coil cleaned. The contactor and capacitor are in good condition and the refrigerant levels are within range. No major issues found

Installed new 5-ton Carrier gas system. Installed new supply and return plenums. Installed Ecobee Pro thermostat. Sealed all connections with mastic air lock. Replaced secondary drain pan. Rebuilt and insulated primary drain line. Installed SS2 and SS3 safety float switches. Cleared drain and verified operation. Pressure tested and pulled a vacuum on the line set. Weighed in charge to meet manufacturers specifications. Upsized bedroom bucket and flex duct and sealed to the drywall with mastic.

I performed diagnostic of the system and found that the blower motor has failed. I verified that the motor was receiving the correct 240 volts. I informed the homeowner, and she chose to have the motor replaced at this time. I replaced the blower motor and cycled power at the thermostat. After starting up the system, I noticed that the outdoor condenser fan motor is showing signs of overheating. No other major issues were found. System operational at this time.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. The blower wheel is clean. Condenser fan motor and contactor are in good condition. Condenser capacitor is within value. The refrigerant level is within factory specifications. No major issues found, and the system was running at the time of departure.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. The wiring is tight and in good condition. The blower motor capacitor is within value. The heat exchanger on this furnace is rusting. Condenser coil clean. Capacitor and condenser fan motor are both within value. Contactor is in good condition. System is cooling at 9.5 degrees of sub cooling. No other major issues found.

Single system cool check completed on a gas system. Electrical tightened and amp draws are within range. The drain line cleared and treated. Both float switches checked and are working properly. Condenser coils cleaned from inside to out. Amp draws and all electrical within manufacture specs. Refrigerant level good. The system is cooling properly at time of departure.

The homeowner reported that the upstairs is not keeping up with the set temp on the thermostat. Checked air filter and in was in good condition. Checked the float switch in the attic and found the primary drain line backed up. Cleared the drain line and monitored the system for 15 minutes including refrigerant levels. System is running properly at this time.

Single system cooling check completed on an up-flow gas system. All electrical and amp draws are within range. The drain line cleared and treated. Float switched checked and is operational. Condenser coil clean. Contactor and capacitor within range. Amp draw on fan and compressor also within range. Refrigerant levels good. No major issues found, and the system is cooling properly at this time.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. Return and supply plenums are clean. The blower wheel is also clean. The wiring is tight and in good condition. The blower motor capacitor is within value. Condenser fan motor and contactor are in good condition. Capacitor for the condenser unit is within value. The refrigerant level was within factory specifications. Condenser coil clean. No major issues were found, and the system was running at the time of departure.

Single system cooling check completed on a horizontal gas system. Cleared and treated the condensation drain line. Inside system clean and all electrical is tight and in value. Outdoor condenser coils clean. Checked amp draws and they are within range. Capacitor value is also within range. The contactor is charred and pitted. No other major issues found.

Single system cooling check completed on an up-flow gas system. The drain line was cleared and treated. The float switch was checked and is working properly. Replaced one 1-inch filter with a customer supplied filter. Condenser coils cleaned. Capacitor within range. Amp draws also within range. Contactor is pitted and charred. The condenser fan motor is leaking oil. Refrigerant levels within range. No other major issues found.

Installed Carrier heat pump system. Installed Ecobee thermostat. Installed plywood overlay. Transitioned to existing supply plenum. Sealed all connections with mastic air lock. Rebuilt and insulated primary drain line. Installed SS2 float switch. Cleared and treated drain to verified operation. Replaced disconnect and whip at outdoor unit. Pressure tested and pulled a vacuum. Weighed in charge to meet manufacturer specifications.