Wimberley TX Heating & Air Conditioning Services

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The blower wheel and evaporator coil are both clean. The wiring is tight and in good condition. The drain line was cleared and treated. The condenser fan motor and contactor are both in good condition. The capacitor for the condenser unit is within value. The refrigerant charge is also within factory specifications. No major issues were found, and the system is running at the time of departure.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared and treated. The blower wheel is clean. The electrical wiring is tight and in good condition. The condenser fan motor is showing signs of overheating. The capacitor is within value. The contactor is in good condition and the refrigerant charge is within factory specifications. No other major issues found.

Installed new Carrier 2-ton heat pump system. Installed new Ecobee Pro thermostat. Rebuilt and insulated condensate drain line. Added SS2 and SS3 safety float switches. Cleared drain line with CO2 and ran three gallons of water to ensure proper operation. We then followed that with Viper drain treatment. Installed new filter dryer, pressure tested with dry nitrogen and pulled a vacuum on copper line set. Replace the condenser pad. Ran the low voltage in Seal-Tite. Replaced both supply and return plenums and sealed with a mastic airlock. Charged system to factory spec and performed a benchmark. The system is working properly at the time of departure.

Installed new condenser fan motor and new suction line thermistor on the main downstairs AC unit. I cleared all previous fault codes on the UI controller and tested the AC system on 100% demand cooling mode. Inspected all Performance, Mechanical and Safety Systems. Verified all temperatures were within operating range. Everything is working at this time. Set thermostat back to schedule mode.

Installed air purifiers on the upstairs and downstairs systems. Replaced the loft mini split head. Reconnected the flare fitting and performed a pressure test on the system. Pulled a vacuum on the system to remove any non condensables from the system. Charged the system to factory specs and checked operation of the system. Check for proper drain operation.

Completed cool check. Cleared and treated the drain line. Washed outdoor condenser coils. I did find low refrigerant in 13-year-old heat pump. Was unable to pinpoint the location of the leak so it may be in the line set. Presented repair options and the homeowner has chosen to have refrigerant added today. Completed repair and function checked the system. The system is currently operational and cooling.

Single system cool check completed on a horizontal heat pump system. The evaporator coil is clean and so is the blower wheel. The drain lines have been cleared and treated. The float switch was checked and is working properly. The air filter has been replaced. The condenser coils have been cleaned and all electrical within manufacture specs. Refrigerant level also within manufacture specs. The condenser fan motor is leaking lubricant. No other major issues found.

Performed service diagnostic and found that the capacitor on the condenser unit has failed. Options for repair were presented to the homeowner and they chose to have the capacitor replaced today. I replaced the capacitor for the condenser unit and cycled the thermostat. The system is running at the time of departure.

Performed cooling maintenance on a heat pump system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. Customer replaced the filter before my arrival. All surge protectors are operational. I found that the secondary drain line does not have a water safety switch on it. I informed the homeowner, and he chose to have one installed today. I installed the water safety switch and reset the breaker. System operational. No other major issues were found.

Performed cooling maintenance on one heat pump system. Checked all electrical mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. I did find that this system needs a hard start kit for the compressor. I installed a hard start kit for a 3-ton system (covered under Garner AC warranty). After installing it I reset the breaker and cycled power at the thermostat. No other major issues were found, and the system is operational at this time.

Installed new Carrier 2-ton system. Installed Ecobee Lite thermostat. Rebuilt and insulated condensate drain line. Added SS2 and SS3 safety float switches. Installed new filter dryer, pressure tested with dry nitrogen and pulled a vacuum on copper line set. Replace the condenser pad. Ran the low voltage in Seal-Tite. Replaced both supply and return plenums and sealed with a mastic airlock. Charged system to factory spec and performed a benchmark. System is working properly at time of departure.

Service diagnostic found that the drain line was clogged. The sink that the drain line flows into is also slowly draining. The vent on the drain line is not higher than the connection to the primary pan under the evaporator coil. This is causing water to spill out into the attic. Options for repair were presented to the customer and they chose to have the drain line cleared today. I cleared the drain line and flow tested the drain with 2.5 gallons of water. I also treated the drain. I extended the vent pipe so that it is above the primary drain connection. This will allow water to flow into the float switch if the drain is clogged again. System was function checked and is running at the time of departure.

Performed AC cool check. Checked electrical, mechanical, safety, and performance of the system. The drain line was cleared, and flow tested with water. The drain line was then treated. The air handler, evaporator coil and blower wheel are all clean. The wiring is tight and in good condition. System sterilizers are operational. The condenser coil is clean. Condenser fan motor and contactor are in good condition. Condenser capacitor is within value. The refrigerant charge is within factory specifications. No major issues were found, and the system is running at the time of departure.

Performed cooling maintenance on one heat pump system. Checked all electrical mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. No major issues were found, and the system is operational at this time.

Performed service diagnostic. Diagnostic found that the contactor in the condenser unit has failed is not passing power. Options for repair were presented to the customer and she chose to have the contactor replaced. Complete repair and the system is now operational.

Performed AC cool check on two systems. Main house: Found some mold/mildew growing inside the air handler. The electrical is tight and in good condition. The drain line was cleared and treated. The condenser fan motor is showing signs of overheating. The capacitor is within value and the refrigerant is within factory specifications. Mini split: System is operating normally and has a 15-degree temperature split. No other major issues were found.

Two system cool check completed: one mini split system and one heat pump system. Found the air filter in the air handler to be dirty and replaced air filter at the customer’s request. Both coils and blower motors are clean. Drain lines cleared. Float switches checked and both are operational. Outdoor coils cleaned and all electrical within manufacture specs. I did find damage on the condenser coils which was likely from the recent hailstorm. Used electronic leak detector and found no leaks. No other major issues found.

Performed cooling maintenance on one heat pump system. Checked all electrical, mechanical and performance of the system. Cleared and treated the drain line and washed the outdoor coil. All surge protectors are operational. No major issues were found.

Performed semiannual maintenance on one heat pump cooling system. Inspected all Performance, Mechanical and safety systems. Changed out one homeowner supplied AprilAire 310 filter. Verified all Breathe Easy systems are operating as designed. System is operating with a 10°SC and a 10°SH. Everything is working at this time.

Performed AC cool check on four systems. Checked electrical, mechanical, safety, and performance of the systems. Drain lines were cleared and treated. Three of the systems have condenser fan motors showing signs of overheating. No other major issues were found, and the systems were running at the time of departure.